- 您現在的位置：買賣IC網 > PDF目錄17059 > EVAL-AD7781EBZ (Analog Devices Inc)BOARD EVAL FOR AD7781 PDF資料下載
參數資料
| 型號： | EVAL-AD7781EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD7781 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 20 |
| 采樣率（每秒）： | 470 |
| 數據接口： | SPI? |
| 輸入范圍： | ±5 V |
| 工作溫度： | -40°C ~ 105°C |
| 已用 IC / 零件： | AD7781 |
| 已供物品： | 板 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
AD7781
Rev. 0 | Page 12 of 16
POWER-DOWN/RESET (PDRST)
The PDRST pin functions as a power-down pin and a reset pin.
When PDRST is taken low, the AD7781 is powered down. The
entire ADC is powered down (including the on-chip clock), the
low-side power switch is opened, and the DOUT/RDY pin is
tristated. The circuitry and serial interface are also reset, which
resets the logic, the digital filter, and the analog modulator.
PDRST must be held low for 100 ns minimum to initiate the
reset function (see
).
When PDRST is taken high, the AD7781 is taken out of power-
down mode. When the on-chip clock has powered up (1 ms,
typically), the modulator begins sampling the analog input.
The low-side power switch is closed, and the DOUT/RDY pin
becomes active.
A reset is automatically performed on power-up.
ANALOG INPUT CHANNEL
The AD7781 has one differential analog input channel. The
input channel feeds into a high impedance input stage of the
amplifier. Therefore, the input can tolerate significant source
impedances and is tailored for direct connection to external
resistive-type sensors such as strain gages.
The absolute input voltage range is restricted to a range between
GND + 450 mV and AVDD 1.1 V. Care must be taken in setting
up the common-mode voltage to avoid exceeding these limits.
Otherwise, there is degradation in linearity and noise performance.
The low noise in-amp means that signals of small amplitude can
be amplified within the AD7781, which still maintains excellent
noise performance. The amplifier can be configured to have a gain
of 128 or 1, using the GAIN pin. The analog input range is equal
to ±VREF/gain. The common-mode voltage (AIN(+) + AIN())/2
must be ≥0.5 V.
BIPOLAR CONFIGURATION
The AD7781 accepts a bipolar input range. A bipolar input range
does not imply that the part can tolerate negative voltages with
respect to system GND. Signals on the AIN(+) input are refer-
enced to the voltage on the AIN() input. For example, if AIN()
is 2.5 V, the analog input range on the AIN(+) input is 2.46 V to
2.54 V for a gain of 128.
DATA OUTPUT CODING
The AD7781 uses offset binary coding. Thus, a negative full-
scale voltage results in a code of 000...000, a zero differential
input voltage results in a code of 100...000, and a positive full-
scale input voltage results in a code of 111...111.
The output code for any analog input voltage can be represented as
Code = 2N 1 × [(AIN × Gain/VREF) + 1]
where:
AIN is the analog input voltage.
Gain is 1 or 128.
N = 20.
REFERENCE
The AD7781 has a fully differential input capability for the channel.
The common-mode range for these differential inputs is GND to
AVDD. The reference input is unbuffered; therefore, excessive R-C
source impedances introduce gain errors. The reference voltage of
REFIN (REFIN(+) REFIN()) is AVDD nominal, but the AD7781
is functional with reference voltages of 0.5 V to AVDD. In applica-
tions where the excitation (voltage or current) for the transducer
on the analog input also drives the reference voltage for the part,
the effect of the low frequency noise in the excitation source is
removed because the application is ratiometric. If the AD7781
is used in a nonratiometric application, a low noise reference
should be used.
Recommended 2.5 V reference voltage sources for the AD7781
references. These references have low output impedances and
are, therefore, tolerant to decoupling capacitors on REFIN(+)
without introducing gain errors in the system. Deriving the
reference input voltage across an external resistor means that
the reference input sees a significant external source impedance.
External decoupling on the REFIN pins is not recommended in
this type of circuit configuration.
BRIDGE POWER-DOWN SWITCH
The bridge power-down switch (BPDSW) is useful in battery-
powered applications where the optimization of system power
consumption is essential. A 350 Ω load cell typically consumes
15 mA when excited with a 5 V power supply. To minimize
current consumption, the load cell is disconnected when it is
not being used. The bridge power-down switch can be included
in series with the load cell. When PDRST is high, the bridge power-
down switch is closed, and the load cell measures the strain. When
PDRST is low, the bridge power-down switch is opened so no
current flows through the load cell. Therefore, the current
consumption of the system is minimized. The bridge power-
down switch has an on resistance of 9 Ω maximum. The switch
is capable of withstanding 30 mA of continuous current.
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2019YM6 TR | IC DISTRIBUTION SW ADJ SOT23-6 |
| MIC2009YML TR | IC DISTRIBUTION SW ADJ 6-MLF |
| EBM28DCTD | CONN EDGECARD 56POS DIP .156 SLD |
| RCM12DSES-S243 | CONN EDGECARD 24POS .156 EYELET |
| VE-B6T-EY | CONVERTER MOD DC/DC 6.5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7782EB | 制造商:Analog Devices 功能描述:READ ONLY, PIN CONFIGURED 24BIT SEGMA-DELTA ADC - Bulk |
| EVAL-AD7783EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-AD7783EBZ | 功能描述:BOARD EVAL FOR AD7783 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7785EBZ | 功能描述:BOARD EVALUATION FOR AD7785 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7787CB | 制造商:Analog Devices 功能描述:DEVELOPMENT BOARD ((NS)) |
發布緊急采購，3分鐘左右您將得到回復。