參數資料
型號： EVAL-AD7691SDZ
廠商： Analog Devices Inc
文件頁數： 11/28頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR AD7691
標準包裝： 1
系列： PulSAR®
ADC 的數量： 1
位數： 18
采樣率（每秒）： 250k
數據接口： 串行
輸入范圍： ±VREF
在以下條件下的電源（標準）： 10.6mW @ 250kSPS，5 V
工作溫度： -40°C ~ 85°C
已用 IC / 零件： AD7691
已供物品： 板
Data Sheet
AD7691
Rev. C | Page 19 of 28
CS MODE, 3-WIRE WITH BUSY INDICATOR
This mode is usually used when a single AD7691 is connected
to an SPI-compatible digital host having an interrupt input.
The connection diagram is shown in Figure 37, and the
corresponding timing is given in Figure 38.
With SDI tied to VIO, a rising edge on CNV initiates a
conversion, selects the CS mode, and forces SDO to high
impedance. SDO is maintained in high impedance until the
completion of the conversion irrespective of the state of CNV.
Prior to the minimum conversion time, CNV can be used to
select other SPI devices, such as analog multiplexers, but CNV
must be returned low before the minimum conversion time
elapses and then held low for the maximum possible conversion
time to guarantee the generation of the busy signal indicator.
When the conversion is complete, SDO goes from high
impedance to low impedance. With a pull-up on the SDO line,
this transition can be used as an interrupt signal to initiate the
data reading controlled by the digital host. The AD7691 then
enters the acquisition phase and powers down. The data bits
are clocked out, MSB first, by subsequent SCK falling edges.
The data is valid on both SCK edges. Although the rising edge
can be used to capture the data, a digital host using the SCK
falling edge can allow a faster reading rate, provided it has an
acceptable hold time. After the optional 19th SCK falling edge,
or when CNV goes high, whichever occurs first, SDO returns to
high impedance.
If multiple AD7691s are selected at the same time, the SDO
output pin handles this contention without damage or induced
latch-up. Meanwhile, it is recommended to keep this contention
as short as possible to limit extra power dissipation.
DATA IN
IRQ
CLK
CONVERT
VIO
DIGITAL HOST
47k
CNV
SCK
SDO
SDI
VIO
AD7691
06
14
6-
0
13
Figure 37. 3-Wire CS Mode with Busy Indicator
Connection Diagram (SDI High)
SDO
D17
D16
D1
D0
tDIS
SCK
123
17
18
19
tSCK
tSCKL
tSCKH
tHSDO
tDSDO
CNV
CONVERSION
ACQUISITION
tCONV
tCYC
ACQUISITION
SDI = 1
tCNVH
tACQ
06
14
6-
0
14
Figure 38. 3-Wire CS Mode with Busy Indicator Serial Interface Timing (SDI High)
相關PDF資料
PDF描述
STD12W-W WIRE & CABLE MARKERS
REC5-0505SRW/H6/A CONV DC/DC 5W 4.5-9VIN 05VOUT
RCM15DRMN CONN EDGECARD 30POS .156 WW
STD12W-S WIRE & CABLE MARKERS
ADR425ARMZ-REEL7 IC VREF SERIES PREC 5V 8-MSOP
相關代理商/技術參數
參數描述
EVAL-AD7693CB 制造商:Analog Devices 功能描述:EVAL KIT FOR 16BIT, 0.5 LSB, 500 KSPS PULSARDIFFERENTIAL ADC - Bulk
EVAL-AD7693CBZ 功能描述:BOARD EVALUATION FOR AD7693 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7693SDZ 功能描述:數據轉換 IC 開發工具 EVAL BOARD 16-bit ADC 500kSPS RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
EVAL-AD7694CB 制造商:Analog Devices 功能描述:
EVAL-AD7694CB1 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 250 kSPS PulSAR ADC in MSOP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*