參數資料
型號： EVAL-AD7667CBZ
廠商： Analog Devices Inc
文件頁數： 19/28頁
文件大小： 0K
描述： BOARD EVALUATION FOR AD7667
標準包裝： 1
系列： PulSAR®
ADC 的數量： 1
位數： 16
采樣率（每秒）： 1M
數據接口： 串行，并聯
輸入范圍： ±VREF
在以下條件下的電源（標準）： 133mW @ 1MSPS
工作溫度： -40°C ~ 85°C
已用 IC / 零件： AD7667
已供物品： 板
相關產品： AD7667ACPZ-ND - IC ADC 16BIT UNIPOLAR 48LFCSP
AD7667ACPZRL-ND - IC ADC 16BIT UNIPOLAR 48LFCSP
AD7667ASTZRL-ND - IC ADC 16BIT UNIPOLAR 48LQFP
AD7667ASTZ-ND - IC ADC 16BIT UNIPOLAR 48-LQFP
AD7667
Rev. 0 | Page 26 of 28
MICROPROCESSOR INTERFACING
The AD7667 is ideally suited for traditional dc measurement
applications supporting a microprocessor, and for ac signal
processing applications interfacing to a digital signal processor.
The AD7667 is designed to interface either with a parallel 8-bit
or 16-bit wide interface, or with a general-purpose serial port or
I/O ports on a microcontroller. A variety of external buffers can
be used with the AD7667 to prevent digital noise from coupling
into the ADC. The following section discusses the use of an
AD7667 with an ADSP-219x SPI equipped DSP.
SPI Interface (ADSP-219x)
Figure 44 shows an interface diagram between the AD7667 and
the SPI equipped ADSP-219x. To accommodate the slower
speed of the DSP, the AD7667 acts as a slave device and data
must be read after conversion. This mode also allows the daisy-
chain feature. The convert command can be initiated in
response to an internal timer interrupt. The reading process can
be initiated in response to the end-of-conversion signal (BUSY
going LOW) using an interrupt line of the DSP. The serial inter-
face (SPI) on the ADSP-219x is configured for master mode—
(MSTR) = 1, Clock Polarity bit (CPOL) = 0, Clock Phase bit
(CPHA) = 1, and SPI Interrupt Enable (TIMOD) = 00—by
writing to the SPI control register (SPICLTx). To meet all timing
requirements, the SPI clock should be limited to 17 Mbps,
which allows it to read an ADC result in less than 1 s. When a
higher sampling rate is desired, use of one of the parallel
interface modes is recommended.
AD7667*
ADSP-219x*
SER/PAR
PFx
MISOx
SCKx
PFx or TFSx
BUSY
SDOUT
SCLK
CNVST
EXT/INT
CS
RD
INVSCLK
DVDD
* ADDITIONAL PINS OMITTED FOR CLARITY
SPIxSEL (PFx)
03035-0-037
Figure 44. Interfacing the AD7667 to an SPI Interface
相關PDF資料
PDF描述
P1020RDB-PA BOARD REFERENCE DESIGN P1020
0210490967 CABLE JUMPER 1.25MM .051M 27POS
MPC8536E-ANDROID HARDWARE/SOFTWARE ANDROID OS
0210490966 CABLE JUMPER 1.25MM .051M 27POS
0210391099 CABLE JUMPER 1MM .051M 39POS
相關代理商/技術參數
參數描述
EVAL-AD7668CB 制造商:AD 制造商全稱:Analog Devices 功能描述:Evaluation Board AD766X/AD767X
EVAL-AD766XCB 制造商:AD 制造商全稱:Analog Devices 功能描述:Evaluation Board AD766X/AD767X
EVAL-AD7671CB 制造商:AD 制造商全稱:Analog Devices 功能描述:Evaluation Board AD766X/AD767X
EVAL-AD7671CBZ 功能描述:BOARD EVALUATION FOR AD7671 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7671EDZ 功能描述:BOARD EVAL FOR AD7671 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*