參數資料
型號： EVAL-AD7634CBZ
廠商： Analog Devices Inc
文件頁數： 17/32頁
文件大?。?/td> 0K
描述： EVAL KIT AD7634
標準包裝： 1
系列： *
其它名稱： Q6500730
AD7634
Data Sheet
Rev. B | Page 24 of 32
INTERFACES
DIGITAL INTERFACE
The AD7634 has a versatile digital interface that can be set up as
either a serial or a parallel interface with the host system. The
serial interface is multiplexed on the parallel data bus. The AD7634
digital interface also accommodates 2.5 V, 3.3 V, or 5 V logic. In
most applications, the OVDD supply pin is connected to the host
system interface 2.5 V to 5.25 V digital supply. Finally, by using the
D0/OB/2C input pin, both twos complement or straight binary
coding can be used, except for in a 18-bit parallel interface.
Two signals, CS and RD, control the interface. When at least
one of these signals is high, the interface outputs are in high
impedance. Usually, CS allows the selection of each AD7634
in multicircuit applications and is held low in a single AD7634
design. RD is generally used to enable the conversion result on
the data bus.
RESET
The RESET input is used to reset the AD7634. A rising edge on
RESET aborts the current conversion (if any) and tristates the
data bus. The falling edge of RESET resets the AD7634 and clears
the data bus and configuration register. See Figure 36 for the
RESET timing details.
t9
t8
RESET
DATA
BUS
BUSY
CNVST
0
6
406
-03
4
Figure 36. RESET Timing
PARALLEL INTERFACE
The AD7634 is configured to use the parallel interface when
the MODE[1:0] pins = 0, 1 or 2 for 18-/16-/8-bit interfaces,
respectively, as detailed in Table 7.
Master Parallel Interface
Data can be continuously read by tying CS and RD low, thus
requiring minimal microprocessor connections. However, in
this mode, the data bus is always driven and cannot be used in
shared bus applications (unless the device is held in RESET).
Figure 37 details the timing for this mode.
t1
BUSY
DATA
BUS
PREVIOUS CONVERSION DATA
NEW DATA
CNVST
CS = RD = 0
t10
t4
t11
t3
0
6406
-035
Figure 37. Master Parallel Data Timing for Reading (Continuous Read)
Slave Parallel Interface
In slave parallel reading mode, the data can be read either after
each conversion, which is during the next acquisition phase, or
during the following conversion, as shown in Figure 38 and
Figure 39, respectively. When the data is read during the conver-
sion, it is recommended that it is read-only during the first half
of the conversion phase. This avoids any potential feedthrough
between voltage transients on the digital interface and the most
critical analog conversion circuitry.
CURRENT
CONVERSION
t13
t12
BUSY
DATA
BUS
RD
CS
06
40
6-
03
6
Figure 38. Slave Parallel Data Timing for Reading (Read After Convert)
PREVIOUS
CONVERSION
t13
t12
t3
BUSY
DATA
BUS
CNVST,
RD
CS = 0
t4
t1
06
40
6-
0
37
Figure 39. Slave Parallel Data Timing for Reading (Read During Convert)
相關PDF資料
PDF描述
VI-271-EY CONVERTER MOD DC/DC 12V 50W
RCB10DHND CONN EDGECARD 20POS DIP .050 SLD
0982660865 CBL 17POS 0.5MM JMPR TYPE A 6"
VI-J4B-EY CONVERTER MOD DC/DC 95V 50W
XRD98L63EVAL EVAL BOARD FOR XRD98L63
相關代理商/技術參數
參數描述
EVAL-AD7634EDZ 功能描述:BOARD EVAL FOR AD7634 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7641CB 制造商:Analog Devices 功能描述:EVAL FOR AD7641CB - Bulk
EVAL-AD7641CB1 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 2 MSPS SAR ADC
EVAL-AD7641CBZ 功能描述:BOARD EVALUATION FOR AD7641 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7641EDZ 功能描述:BOARD EVAL FOR AD7641 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*