參數資料
型號： EVAL-AD7192EBZ
廠商： Analog Devices Inc
文件頁數： 24/41頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR AD7192
標準包裝： 1
ADC 的數量： 1
位數： 24
采樣率（每秒）： 4.8k
數據接口： SPI?、QSPI?、MICROWIRE? 和 DSP
輸入范圍： ±VREF/增益
工作溫度： -40°C ~ 105°C
已用 IC / 零件： AD7192
已供物品： 板
AD7192
Rev. A | Page 29 of 40
Single Conversion Mode
line returns high after the first read operation. However, care
must be taken to ensure that the read operations are completed
before the next output update occurs. In continuous read mode,
the data register can be read only once.
In single conversion mode, the AD7192 is placed in power-
down mode after conversions. When a single conversion is
initiated by setting MD2, MD1, and MD0 to 0, 0, 1, respectively,
in the mode register, the AD7192 powers up, performs a single
conversion, and then returns to power-down mode. The on-
chip oscillator requires 1 ms, approximately, to power up.
The serial interface can operate in 3-wire mode by tying CS low.
In this case, the SCLK, DIN, and DOUT/RDY lines are used to
communicate with the AD7192. The end of the conversion can be
monitored using the RDY bit or pin. This scheme is suitable for
interfacing to microcontrollers. If CS is required as a decoding
signal, it can be generated from a port pin. For microcontroller
interfaces, it is recommended that SCLK idle high between data
transfers.
DOUT/RDY goes low to indicate the completion of a conver-
sion. When the data-word has been read from the data register,
DOUT/RDY goes high. If CS is low, DOUT/RDY remains high
until another conversion is initiated and completed. The data
register can be read several times, if required, even when
DOUT/RDY has gone high.
The AD7192 can be operated with CS used as a frame synchro-
nization signal. This scheme is useful for DSP interfaces. In this
case, the first bit (MSB) is effectively clocked out by CS because
CS normally occurs after the falling edge of SCLK in DSPs. The
SCLK can continue to run between data transfers, provided the
timing numbers are obeyed.
If several channels are enabled, the ADC sequences through the
enabled channels and performs a conversion on each channel.
When a conversion is started, DOUT/RDY goes high and
remains high until a valid conversion is available. As soon as the
conversion is available, DOUT/RDY goes low. The ADC then
selects the next channel and begins a conversion. The user can
read the present conversion while the next conversion is being
performed. As soon as the next conversion is complete, the data
register is updated; therefore, the user has a limited period in
which to read the conversion. When the ADC has performed a
single conversion on each of the selected channels, it returns to
power-down mode.
The serial interface can be reset by writing a series of 1s to the
DIN input. If a Logic 1 is written to the AD7192 DIN line for at
least 40 serial clock cycles, the serial interface is reset. This
ensures that the interface can be reset to a known state if the
interface gets lost due to a software error or some glitch in the
system. Reset returns the interface to the state in which it expects
a write to the communications register. This operation resets the
contents of all registers to their power-on values. Following a
reset, the user should allow a period of 500 μs before addressing
the serial interface.
If the DAT_STA bit in the mode register is set to 1, the contents
of the status register are output along with the conversion each
time that the data read is performed. The four LSBs of the status
register indicate the channel to which the conversion corresponds.
The AD7192 can be configured to continuously convert or to
perform a single conversion (see Figure 29 through Figure 31).
DIN
SCLK
DOUT/RDY
CS
0x08
0x58
DATA
0x280060
0
78
22-
021
Figure 29. Single Conversion
相關PDF資料
PDF描述
LQH3NPN220MJ0L INDUCTOR POWER 22UH 510MA 1212
PCMC063T-R68MN COIL .68UH POWER CHOKE 20% SMD
EVAL-AD7190EBZ BOARD EVAL FOR AD7190
EBM25DRSN CONN EDGECARD 50POS DIP .156 SLD
PCMC063T-R22MN COIL .22UH POWER CHOKE 20% SMD
相關代理商/技術參數
參數描述
EVAL-AD7192EBZ 制造商:Analog Devices 功能描述:EVAL BOARD, AD7192 24BIT ADC
EVAL-AD7193EBZ 功能描述:EVAL BOARD FOR AD7193 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7194EBZ 功能描述:EVAL BOARD FOR AD7194 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7195EBZ 功能描述:BOARD EVAL FOR AD7195 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
EVAL-AD7262EDZ 功能描述:BOARD EVAL CONTROL AD7262 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*