- 您現在的位置：買賣IC網 > PDF目錄17076 > EVAL-AD5754REBZ (Analog Devices Inc)BOARD EVAL FOR AD5754R PDF資料下載
參數資料
| 型號： | EVAL-AD5754REBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 24/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD5754R |
| 標準包裝： | 1 |
| DAC 的數量： | 4 |
| 位數： | 16 |
| 采樣率（每秒）： | * |
| 數據接口： | 串行 |
| 設置時間： | 10µs |
| DAC 型： | 電壓 |
| 工作溫度： | -40°C ~ 85°C |
| 已供物品： | 板 |
| 已用 IC / 零件： | AD5754 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD5724R/AD5734R/AD5754R
Rev. E | Page 30 of 32
DESIGN FEATURES
ANALOG OUTPUT CONTROL
In many industrial process control applications, it is vital that
the output voltage be controlled during power-up. When the
supply voltages change during power-up, the VOUTx pins are
clamped to 0 V via a low impedance path (approximately 4 kΩ).
To prevent the output amplifiers from being shorted to 0 V
during this time, Transmission Gate G1 is also opened (see
Figure 48). These conditions are maintained until the power
supplies have stabilized and a valid word is written to a DAC
register. At this time, G2 opens and G1 closes.
VOUTA
G1
G2
VOLTAGE
MONITOR
AND
CONTROL
0
64
65
-0
10
Figure 48. Analog Output Control Circuitry
POWER-DOWN MODE
Each DAC channel of the AD5724R/AD5734R/AD5754R can
be individually powered down. By default, all channels are in
power-down mode. The power status is controlled by the power
channel is in power-down mode its output pin is clamped to
ground through a resistance of approximately 4 kΩ and the
output of the amplifier is disconnected from the output pin.
OVERCURRENT PROTECTION
Each DAC channel of the AD5724R/AD5734R/AD5754R
incorporates individual overcurrent protection. The user has
two options for the configuration of the overcurrent protection:
constant current clamp or automatic channel power-down. The
configuration of the overcurrent protection is selected via the
clamp enable bit in the control register.
Constant Current Clamp (Clamp Enable = 1)
If a short circuit occurs in this configuration, the current is
clamped at 20 mA. This event is signaled to the user by the
setting of the appropriate overcurrent (OCX) bit in the power
control register. Upon removal of the short-circuit fault, the
OCX bit is cleared.
Automatic Channel Power-Down (Clamp Enable = 0)
If a short circuit occurs in this configuration, the shorted
channel powers down and its output is clamped to ground via
a resistance of approximately 4 kΩ. Also, at this time, the output
of the amplifier is disconnected from the output pin. The short-
circuit event is signaled to the user via the overcurrent bits (OCX),
while the power-up bits (PUX) indicate which channels have
powered down. After the fault is rectified, the channels can be
powered up again by setting the PUX bits.
THERMAL SHUTDOWN
The AD5724R/AD5734R/AD5754R incorporate a thermal
shutdown feature that automatically shuts down the device if
the core temperature exceeds approximately 150°C. The thermal
shutdown feature is disabled by default and can be enabled
via the TSD enable bit of the control register. In the event of a
thermal shutdown, the TSD bit of the power control register is set.
INTERNAL REFERENCE
The on-chip voltage reference is powered down by default. If
an external voltage reference source is to be used, the internal
reference must remain powered down at all times. If the internal
reference is to be used as the reference source, it must be powered
up via the PUREF bit of the power control register. The internal
reference voltage is accessible at the REFIN/REFOUT pin for use
as a reference source for other devices within the system. If the
internal reference is to be used external to the AD5724R/
AD5734R/AD5754R, it must first be buffered.
相關PDF資料 |
PDF描述 |
|---|---|
| NRS5020T6R8MMGJ | INDUCTOR 6.8UH 1.65A 20% SMD |
| AP2146MPG-13 | IC USB PWR SWITCH .5A DUAL 8MSOP |
| 380LX472M035J012 | CAP ALUM 4700UF 35V 20% SNAP |
| EVAL-AD5443SDZ | BOARD EVAL FOR AD5443 |
| ESA10DTBD | CONN EDGECARD 20POS R/A .125 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD5755-1SDZ | 功能描述:BOARD EVAL FOR AD5755-1 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5755SDZ | 功能描述:BOARD EVAL FOR AD5755 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5757SDZ | 功能描述:BOARD EVAL FOR AD5757 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5760SDZ | 功能描述:BOARD EVAL FOR AD5760SDZ RoHS:否 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5764EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD FOR QUAD, 16-BIT, HIGH ACCURACY, SERIAL INPUT, BIPOLAR VOLTAGE OUTPUT DAC 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD I.C. - Bulk |
發布緊急采購，3分鐘左右您將得到回復。