參數資料
型號： EVAL-AD5371EBZ
廠商： Analog Devices Inc
文件頁數： 13/29頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR AD5371
產品培訓模塊： DAC Architectures
標準包裝： 1
DAC 的數量： 40
位數： 14
采樣率（每秒）： 540k
數據接口： 串行
設置時間： 20µs
DAC 型： 電壓
工作溫度： -40°C ~ 85°C
已供物品： 板，CD
已用 IC / 零件： AD5371
相關產品： AD5371BSTZ-REEL-ND - IC DAC 14BIT 40CH SER 80-LQFP
AD5371BBCZ-REELTR-ND - IC DAC 14BIT 40CH SER 100-CSPBGA
AD5371
Rev. B | Page 19 of 28
Reference Selection Example
If
Nominal output range = 12 V (4 V to +8 V)
Zero-scale error = ±70 mV
Gain error = ±3%, and
SIGGNDx = AGND = 0 V
Then
Gain error = ±3%
=> Maximum positive gain error = 3%
=> Output range including gain error = 12 + 0.03(12) = 12.36 V
Zero-scale error = ±70 mV
=> Maximum offset error span = 2(70 mV) = 0.14 V
=> Output range including gain error and zero-scale error =
12.36 V + 0.14 V = 12.5 V
VREF calculation
Actual output range = 12.5 V, that is, 4.25 V to +8.25 V;
VREF = (8.25 V + 4.25 V)/4 = 3.125 V
If the solution yields an inconvenient reference level, the user
can adopt one of the following approaches:
Use a resistor divider to divide down a convenient, higher
reference level to the required level.
Select a convenient reference level above VREF and modify
the gain and offset registers to digitally downsize the reference.
In this way, the user can use almost any convenient reference
level but can reduce the performance by overcompaction of
the transfer function.
Use a combination of these two approaches.
CALIBRATION
The user can perform a system calibration on the AD5371 to
reduce gain and offset errors to below 1 LSB. This reduction is
achieved by calculating new values for the M and C registers and
reprogramming them.
The M and C registers should not be programmed until both
the zero-scale and full-scale errors are calculated.
Reducing Zero-Scale Error
Zero-scale error can be reduced as follows:
1.
Set the output to the lowest possible value.
2.
Measure the actual output voltage and compare it to the
required value. This gives the zero-scale error.
3.
Calculate the number of LSBs equivalent to the error and
add this number to the default value of the C register. Note
that only negative zero-scale error can be reduced.
Reducing Full-Scale Error
Full-scale error can be reduced as follows:
1.
Measure the zero-scale error.
2.
Set the output to the highest possible value.
3.
Measure the actual output voltage and compare it to the
required value. Add this error to the zero-scale error. This
is the span error, which includes the full-scale error.
4.
Calculate the number of LSBs equivalent to the span error
and subtract this number from the default value of the M
register. Note that only positive full-scale error can be
reduced.
AD5371 Calibration Example
This example assumes that a 4 V to +8 V output is required.
The DAC output is set to 4 V but measured at 4.03 V. This
gives a zero-scale error of 30 mV.
1 LSB = 12 V/16,384 = 732.42 μV
30 mV = 41 LSBs
The full-scale error can now be calculated. The output is set to
8 V and a value of 8.02 V is measured. This gives a full-scale
error of +20 mV and a span error of +20 mV (30 mV) =
+50 mV.
50 mV = 68 LSBs
The errors can now be removed as follows:
1.
Add 41 LSBs to the default C register value:
8192 + 41 = 8233
2.
Subtract 68 LSBs from the default M register value:
16,383 68 = 16,315
3.
Program the M register to 16,315; program the C register
to 8233.
ADDITIONAL CALIBRATION
The techniques described in the previous section are usually
enough to reduce the zero-scale and full-scale errors in most
applications. However, there are limitations whereby the errors
may not be sufficiently reduced. For example, the offset (C)
register can only be used to reduce the offset caused by the
negative zero-scale error. A positive offset cannot be reduced.
Likewise, if the maximum voltage is below the ideal value, that
is, a negative full-scale error, the gain (M) register cannot be
used to increase the gain to compensate for the error.
These limitations can be overcome by increasing the reference
value. With a 3 V reference, a 12 V span is achieved. The ideal
voltage range for the AD5371 is 4 V to +8 V. Using a +3.1 V
reference increases the range to 4.133 V to +8.2667 V. Clearly,
in this case, the offset and gain errors are insignificant, and the
M and C registers can be used to raise the negative voltage to
4 V and then reduce the maximum voltage to +8 V to give the
most accurate values possible.
相關PDF資料
PDF描述
EMC05DRTF-S13 CONN EDGECARD 10POS .100 EXTEND
SC53LC-470 INDUCTOR SMD 47UH 0.62A 100KHZ
V375C2E50BF CONVERTER MOD DC/DC 2V 50W
101-1102 KIT DEV RABBIT RCM4100 INTL
RCC17DRXN CONN EDGECARD 34POS DIP .100 SLD
相關代理商/技術參數
參數描述
EVAL-AD5372EBZ 功能描述:BOARD EVAL FOR AD5372 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5373EBZ 功能描述:BOARD EVAL FOR AD5373 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5379EB 制造商:AD 制造商全稱:Analog Devices 功能描述:40-Channel, 14-Bit, Parallel and Serial Input, Bipolar Voltage-Output DAC
EVAL-AD5379EBZ 功能描述:BOARD EVALUATION FOR AD5379 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5380EB 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*