參數資料
型號： EVAL-AD5362EBZ
廠商： Analog Devices Inc
文件頁數： 13/29頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR AD5362
產品培訓模塊： DAC Architectures
標準包裝： 1
DAC 的數量： 8
位數： 16
采樣率（每秒）： 540k
數據接口： 串行
設置時間： 20µs
DAC 型： 電壓
工作溫度： -40°C ~ 85°C
已供物品： 板，CD
已用 IC / 零件： AD5362
相關產品： AD5362BSTZ-REEL-ND - IC DAC 16BIT 8CH SERIAL 52-LQFP
AD5362BSTZ-ND - IC DAC 16BIT 8CH SERIAL 52-LQFP
AD5362BCPZ-REEL7-ND - IC DAC 16BIT 8CH SERIAL 56-LFCSP
AD5362BCPZ-ND - IC DAC 16BIT 8CH SERIAL 56-LFCSP
AD5362/AD5363
Rev. A | Page 19 of 28
Reference Selection Example
If
Nominal output range = 20 V (10 V to +10 V)
Offset error = ±100 mV
Gain error = ±3%, and
SIGGND = AGND = 0 V
Then
Gain error = ±3%
=> Maximum positive gain error = 3%
=> Output range including gain error = 20 + 0.03(20) = 20.6 V
Offset error = ±100 mV
=> Maximum offset error span = 2(100 mV) = 0.2 V
=> Output range including gain error and offset error =
20.6 V + 0.2 V = 20.8 V
VREF calculation
Actual output range = 20.6 V, that is, 10.3 V to +10.3 V
(centered);
VREF = (10.3 V + 10.3 V)/4 = 5.15 V
If the solution yields an inconvenient reference level, the user
can adopt one of the following approaches:
Use a resistor divider to divide down a convenient, higher
reference level to the required level.
Select a convenient reference level above VREF and modify
the gain and offset registers to digitally downsize the reference.
In this way, the user can use almost any convenient reference
level but can reduce the performance by overcompaction of
the transfer function.
Use a combination of these two approaches.
CALIBRATION
The user can perform a system calibration on the AD5362/
AD5363 to reduce gain and offset errors to below 1 LSB. This
reduction is achieved by calculating new values for the M and
C registers and reprogramming them.
The M and C registers should not be programmed until both
the zero-scale and full-scale errors are calculated.
Reducing Zero-Scale Error
Zero-scale error can be reduced as follows:
1.
Set the output to the lowest possible value.
2.
Measure the actual output voltage and compare it to the
required value. This gives the zero-scale error.
3.
Calculate the number of LSBs equivalent to the error and
add this number to the default value of the C register. Note
that only negative zero-scale error can be reduced.
Reducing Full-Scale Error
Full-scale error can be reduced as follows:
1.
Measure the zero-scale error.
2.
Set the output to the highest possible value.
3.
Measure the actual output voltage and compare it to the
required value. Add this error to the zero-scale error. This
is the span error, which includes the full-scale error.
4.
Calculate the number of LSBs equivalent to the span error
and subtract this number from the default value of the M
register. Note that only positive full-scale error can be
reduced.
AD5362 Calibration Example
This example assumes that a 10 V to +10 V output is required.
The DAC output is set to 10 V but measured at 10.03 V. This
gives a zero-scale error of 30 mV.
1 LSB = 20 V/65,536 = 305.176 μV
30 mV = 98 LSBs
The full-scale error can now be calculated. The output is set to
10 V and a value of 10.02 V is measured. This gives a full-scale
error of +20 mV and a span error of +20 mV – (–30 mV) =
+50 mV.
50 mV = 164 LSBs
The errors can now be removed as follows:
1.
Add 98 LSBs to the default C register value:
(32,768 + 98) = 32,866
2.
Subtract 164 LSBs from the default M register value:
(65,535 164) = 65,371
3.
Program the M register to 65,371; program the C register
to 32,866.
ADDITIONAL CALIBRATION
The techniques described in the previous section are usually
enough to reduce the zero-scale and full-scale errors in most
applications. However, there are limitations whereby the errors
may not be sufficiently reduced. For example, the offset (C)
register can only be used to reduce the offset caused by the
negative zero-scale error. A positive offset cannot be reduced.
Likewise, if the maximum voltage is below the ideal value, that
is, a negative full-scale error, the gain (M) register cannot be
used to increase the gain to compensate for the error.
These limitations can be overcome by increasing the reference
value. With a 2.5 V reference, a 10 V span is achieved. The ideal
voltage range, for the AD5362 or the AD5363, is 5 V to +5 V.
Using a +2.6 V reference increases the range to 5.2 V to +5.2
V.
Clearly, in this case, the offset and gain errors are
insignificant,
and the M and C registers can be used to raise the
negative
voltage to 5 V and then reduce the maximum voltage
to +5 V
to give the most accurate values possible.
相關PDF資料
PDF描述
GCA18DTKT CONN EDGECARD 36POS DIP .125 SLD
VI-BTX-EY CONVERTER MOD DC/DC 5.2V 50W
VI-BTV-EY CONVERTER MOD DC/DC 5.8V 50W
DC1444A-B BOARD SAR ADC LTC2305
HBM08DRYF CONN EDGECARD 16POS DIP .156 SLD
相關代理商/技術參數
參數描述
EVAL-AD5363EBZ 功能描述:BOARD EVALUATION FOR AD5363 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5370EBZ 功能描述:BOARD EVALUATION FOR AD5370 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5371EBZ 功能描述:BOARD EVAL FOR AD5371 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5372EBZ 功能描述:BOARD EVAL FOR AD5372 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5373EBZ 功能描述:BOARD EVAL FOR AD5373 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*