- 您現在的位置：買賣IC網 > PDF目錄16601 > EVAL-AD5292EBZ (Analog Devices Inc)BOARD EVAL FOR AD5292 PDF資料下載
參數資料
| 型號： | EVAL-AD5292EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 17/32頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD5292 |
| 標準包裝： | 1 |
| 主要目的： | 數字電位器 |
| 嵌入式： | 是 |
| 已用 IC / 零件： | AD5292 |
| 主要屬性： | 1 通道，1024 位置 |
| 次要屬性： | SPI 接口 |
| 已供物品： | 板，CD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD5291/AD5292
Rev. D | Page 24 of 32
BASIC OPERATION
The basic mode of setting the variable resistor wiper position
(programming the RDAC register) is accomplished by loading
the shift register with Command 1 (see Table 11) and the desired
wiper position data. When the desired wiper position is deter-
mined, the user can load the shift register with Command 3
(see Table 11), which stores the wiper position data in the 20-TP
memory register. After 6 ms, the wiper position is permanently
stored in the 20-TP memory. The RDY pin can be used to moni-
tor the completion of this 20-TP program. Table 12 provides a
programming example, listing the sequence of serial data input
(DIN) words with the serial data output appearing at the SDO
pin in hexadecimal format.
20-TP READBACK AND SPARE MEMORY STATUS
It is possible to read back the contents of any of the 20-TP
memory registers through SDO by using Command 5 (see
Table 11). The lower five LSB bits (D0 to D4) of the data byte
select which memory location is to be read back (see Table 16).
Data from the selected memory location are clocked out of the
SDO pin during the next SPI operation, where the last 10 bits
contain the contents of the specified memory location.
It is also possible to calculate the address of the most recently
programmed memory location by reading back the contents of
read-only Memory Address 0x14 and Memory Address 0x15
using Command 5. The data bytes read back from Memory
Address 0x014 and Memory Address 0x015 are thermometer
encoded versions of the address of the last programmed
memory location.
For the example outlined in Table 15, the address of the last
programmed location is calculated as
(Number of Bits = 1 in Memory Address 0x14) + (Number
of Bits = 1 in Memory Address 0x15) 1 = 10 + 8 1 = 17
(0x10)
If no memory location has been programmed, then the address
generated is 1.
SHUTDOWN MODE
The AD5291 and AD5292 can be placed in shutdown mode by
executing the software shutdown command, Command 8 (see
Table 11), and setting the LSB, D0, to 1. This feature places the
RDAC in a special state in which Terminal A is open-circuited,
and Wiper W is connected to Terminal B. The contents of the
RDAC register are unchanged by entering shutdown mode.
However, all commands listed in Table 11 are supported while
in shutdown mode. Execute Command 8 (see Table 11), and set
the LSB, D0, to 0 to exit shutdown mode.
Table 15. Example 20-TP Memory Readback
DIN
SDO
Action
0x1414
0xXXXX
Prepares data read from Memory Address 0x14.
0x1415
0x03FF
Prepares data read from Memory Address 0x15. Sends 16-bit word out of SDO, where the last 10 bits contain the
contents of Memory Address 0x14.
0x0000
0x00FF
NOP Command 0 sends 16-bit word out of SDO, where last 10-bits contain the contents of Memory Address 0x15.
0x1410
0x0000
Prepares data read from memory location 0x10.
0x0000
0xXXXX
NOP Instruction 0 sends 16-bit word out of SDO, where the last 10 bits contain the contents of Memory Address 0x10 (17).
Table 16. Memory Map of Command 5
Data Bits [DB9:DB0]1
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Register Contents
X
0
1st programmed wiper location (0x00)
X
0
1
2nd programmed wiper location (0x01)
X
0
1
0
3rd programmed wiper location (0x02)
X
0
1
4th programmed wiper location (0x03)
X
0
1
0
5th programmed wiper location (0x04)
…
X
0
1
0
1
10th programmed wiper location (0x09)
X
0
1
0
15th programmed wiper location (0x0E)
X
1
0
1
20th programmed wiper location (0x13)
X
1
0
1
0
Programmed memory status (thermometer encoded)2 (0x14)
X
1
0
1
0
1
Programmed memory status (thermometer encoded)2 (0x15)
1 X = don’t care.
2 Allows the user to calculate the remaining spare memory locations.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B3N-EW | CONVERTER MOD DC/DC 18.5V 100W |
| VI-B3K-EX | CONVERTER MOD DC/DC 40V 75W |
| VE-B6P-EX | CONVERTER MOD DC/DC 13.8V 75W |
| VE-B6P-EW | CONVERTER MOD DC/DC 13.8V 100W |
| H3AKH-2018G | IDC CABLE - HSC20H/AE20G/HPK20H |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD5360EBZ | 功能描述:BOARD EVAL FOR AD5360 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5360EBZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Channel, 16-/14-Bit, Serial Input, Voltage-Output DAC |
| EVAL-AD5361EBZ | 功能描述:BOARD EVAL FOR AD5361 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5361EBZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Channel, 16-/14-Bit, Serial Input, Voltage-Output DAC |
| EVAL-AD5362EBZ | 功能描述:BOARD EVAL FOR AD5362 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
發布緊急采購，3分鐘左右您將得到回復。