- 您現在的位置：買賣IC網 > PDF目錄16588 > EVAL-AD5290EBZ (Analog Devices Inc)BOARD EVAL FOR AD5290 PDF資料下載
參數資料
| 型號： | EVAL-AD5290EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD5290 |
| 設計資源： | AD5290 Evaluation Tools |
| 標準包裝： | 1 |
| 主要目的： | 數字電位器 |
| 已用 IC / 零件： | AD5290 |
| 已供物品： | 板 |
| 相關產品： | AD5290YRMZ50-R7-ND - IC POT DGTL 50KW 256POS 10-MSOP AD5290YRMZ10-R7-ND - IC POT DGTL 10KW 256POS 10-MSOP AD5290YRMZ100-R7-ND - IC POT DGTL 100KW 256POS 10-MSOP AD5290YRMZ50-ND - IC DGTL POT 50K 256POS 10MSOP AD5290YRMZ100-ND - IC DGTL POT 100K 256POS 10MSOP AD5290YRMZ10-ND - IC DGTL POT 10K 256POS 10MSOP |
AD5290
Data Sheet
Rev. C | Page 16 of 20
PROGRAMMING THE POTENTIOMETER DIVIDER
Voltage Output Operation
The digital potentiometer easily generates a voltage divider
at wiper to B and wiper to A proportional to the input voltage
at A to B. Unlike the polarity of VDD to GND, which must be
positive, voltage across A to B, W to A, and W to B can be at
either polarity.
A
VI
W
B
VO
04716-013
Figure 28. Potentiometer Mode Configuration
If ignoring the effect of the wiper resistance for simplicity, con-
necting the A terminal to 30 V and the B terminal to ground
produces an output voltage at the Wiper W to Terminal B
ranging from 0 V to 1 LSB less than 30 V. Each LSB of voltage
is equal to the voltage applied across Terminal A and Terminal B,
divided by the 256 positions of the potentiometer divider. The
general equation defining the output voltage at VW with respect
to ground for any valid input voltage applied to Terminal A and
Terminal B is
B
A
W
V
D
V
D
V
×
+
×
=
256
)
(
(3)
Operation of the digital potentiometer in the divider mode
results in a more accurate operation over temperature. Unlike
the rheostat mode, the output voltage is dependent mainly on
the ratio of the internal resistors RWA and RWB and not the
absolute values. Therefore, the temperature drift reduces to
5 ppm/°C.
3-WIRE SERIAL BUS DIGITAL INTERFACE
The AD5290 contains a 3-wire digital interface (CS, CLK,
and SDI). The 8-bit serial word must be loaded MSB first.
The format of the word is shown in Table 4. The positive edge
sensitive CLK input requires clean transitions to avoid clocking
incorrect data into the serial input register. Standard logic fami-
lies work well. When CS is low, the clock loads data into the
serial register on each positive clock edge.
The data setup and data hold times in the Specifications section
determine the valid timing requirements. The AD5290 uses an
8-bit serial input data register word that is transferred to the
internal RDAC register when the CS line returns to logic high.
Extra MSB bits are ignored.
DAISY CHAIN OPERATION
SDO shifts out the SDI content in the previous frame; thus it
can be used for daisy-chaining multiple devices. The SDO pin
contains an open drain N-Ch MOSFET and requires a pull-
up resistor if the SDO function is used. Users need to tie the
SDO pin of one package to the SDI pin of the next package.
Users may need to increase the clock period because the pull-up
resistor and the capacitive loading at the SDO to SDI interface
can induce time delay to the subsequent devices.
For example, in Figure 29, if two AD5290s are daisy-chained, a
total of 16 bits of data are required for each operation. The first
set of eight bits goes to U2, and the second set of eight bits goes
to U1. The CS should be kept low until all 16 bits are clocked
into their respective serial registers. The CS is then pulled high
to complete the operation.
AD5290
U1
SDO
SDI
CLK
CS
AD5290
U2
SDO
SDI
CLK
CS
C
+5V
RPU
2.2k
MOSI
SS
SCLK
04716-
014
Figure 29. Daisy Chain Configuration
相關PDF資料 |
PDF描述 |
|---|---|
| RCA18DTAN | CONN EDGECARD 36POS R/A .125 SLD |
| RCA18DTAH | CONN EDGECARD 36POS R/A .125 SLD |
| RCA18DTAD | CONN EDGECARD 36POS R/A .125 SLD |
| EVAL-ADCMP582BCPZ | BOARD EVALUATION ADCMP582BCP |
| HSM06DRAI | CONN EDGECARD 12POS R/A .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD5292EBZ | 功能描述:BOARD EVAL FOR AD5292 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-AD5360EBZ | 功能描述:BOARD EVAL FOR AD5360 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5360EBZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Channel, 16-/14-Bit, Serial Input, Voltage-Output DAC |
| EVAL-AD5361EBZ | 功能描述:BOARD EVAL FOR AD5361 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5361EBZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Channel, 16-/14-Bit, Serial Input, Voltage-Output DAC |
發布緊急采購，3分鐘左右您將得到回復。