- 您現在的位置：買賣IC網 > PDF目錄16594 > EVAL-AD5232-10EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD5232-10 PDF資料下載
參數資料
| 型號： | EVAL-AD5232-10EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 13/24頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD5232-10 |
| 標準包裝： | 1 |
| 主要目的： | 數字電位器 |
| 已用 IC / 零件： | AD5232 |
| 主要屬性： | 2 通道，256 位置 |
| 已供物品： | 板 |
| 相關產品： | AD5232BRUZ50-ND - IC DGTL POT 256POS 50K 16TSSOP AD5232BRUZ10-REEL7-ND - IC POT DGTL DUAL 256POS 16TSSOP AD5232BRUZ50-REEL7-ND - IC POT DGTL DUAL 256POS 16TSSOP AD5232BRUZ10-ND - IC DGTL POT DUAL 256POS 16-TSSOP AD5232BRUZ100-RL7-ND - IC DGTL POT DUAL 256POS 16-TSSOP AD5232BRUZ100-ND - IC DGTL POT DUAL 256POS 16-TSSOP AD5232BRU50-REEL7-ND - IC DGTL POT DUAL 256POS 16-TSSOP AD5232BRU50-ND - IC DGTL POT DUAL 256POS 16-TSSOP AD5232BRU100REEL7-ND - IC DGTL POT DUAL 256POS 16-TSSOP AD5232BRU100-ND - IC DGTL POT DUAL 256POS 16-TSSOP 更多... |
AD5232
Data Sheet
Rev. C | Page 20 of 24
PROGRAMMING THE POTENTIOMETER DIVIDER
Voltage Output Operation
The digital potentiometer easily generates an output voltage pro-
portional to the input voltage applied to a given terminal. For
example, connecting Terminal A to 5 V and Terminal B to GND
produces an output voltage at the wiper that can be any value
from 0 V to 5 V. Each LSB of voltage is equal to the voltage
applied across Terminal A to Terminal B, divided by the 2N
position resolution of the potentiometer divider. The general
equation defining the output voltage with respect to ground for
any given input voltage applied to Terminal A to Terminal B is
B
AB
WA
A
AB
WB
W
V
R
D
R
V
R
D
R
D
V
×
+
×
=
)
(
)
(
)
(
(3)
where RWB(D) can be obtained from Equation 1 and RWA(D)
can be obtained from Equation 2.
Operation of the digital potentiometer in the divider mode
results in more accurate operation over temperature. Here the
output voltage is dependent on the ratio of the internal resistors,
not the absolute value; therefore, the drift improves to 15 ppm/°C.
There is no voltage polarity restriction between Terminal A,
Terminal B, and Wiper Terminal W as long as the terminal voltage
(VTERM) stays within VSS < VTERM < VDD.
OPERATION FROM DUAL SUPPLIES
The AD5232 can be operated from dual supplies, enabling
control of ground-referenced ac signals (see Figure 42 for
a typical circuit connection).
AD5232
VSS
GND
SDI
CLK
SS
SCLK
MOSI
GND
VDD
±2V p-p
±1V p-p
VDD
+2.5V
–2.5V
CS
02618-
042
MicroConverter
Figure 42. Operation from Dual Supplies
The internal parasitic capacitances and the external capacitive
loads dominate the ac characteristics of the RDACs. When
configured as a potentiometer divider, the 3 dB bandwidth of
the AD5232BRU10 (10 k resistor) measures 500 kHz at half
scale. Figure 14 provides the large signal BODE plot character-
istics of the three resistor versions: 10 k, 50 k, and 100 k (see
Figure 43 for a parasitic simulation model of the RDAC circuit).
A
W
02618-
043
B
RDAC
10k
CA
45pF
CB
45pF
CW
60pF
Figure 43. RDAC Circuit Simulation Model for RDACx = 10 k
The following code provides a macro model net list for the
10 k RDAC:
.PARAM DW=255, RDAC=10E3
*
.SUBCKT DPOT (A,W,B)
*
CA A 0 {45E-12}
RAW A W {(1-DW/256)*RDAC+50}
CW W 0 60E-12
RBW W B {DW/256*RDAC+50}
CB B 0 {45E-12}
*
.ENDS DPOT
APPLICATION PROGRAMMING EXAMPLES
The command sequence examples shown in Table 14 to Table 18
have been developed to illustrate a typical sequence of events
for the various features of the AD5232 nonvolatile digital poten-
tiometer. Table 14 illustrates setting two digital potentiometers
to independent data values.
Table 14.
SDI
SDO
Action
0xB140
0xXXXX
Loads 0x40 data into the RDAC2 register;
Wiper W2 moves to 1/4 full-scale position.
0xB080
0xB140
Loads 0x80 data into the RDAC1 register;
Wiper W1 moves to 1/2 full-scale position.
Table 15 illustrates the active trimming of one potentiometer,
followed by a save to nonvolatile memory (PCB calibrate).
Table 15.
SDI
SDO
Action
0xB040
0xXXXX
Loads 0x40 data into the RDAC1 register;
Wiper W1 moves to 1/4 full-scale position.
0xE0XX
0xB040
Increments the RDAC1 register by 1, to 0x41;
Wiper W1 moves one resistor segment
away from Terminal B.
0xE0XX
Increments the RDAC1 register by 1, to 0x42;
Wiper W1 moves one more resistor segment
away from Terminal B. Continue until
desired the wiper position is reached.
0x20XX
0xE0XX
Saves the RDAC1 register data into the
corresponding nonvolatile EEMEM1
memory: ADDR = 0x0.
相關PDF資料 |
PDF描述 |
|---|---|
| M3BBK-1018J | IDC CABLE - MSR10K/MC10G/MSR10K |
| EVAL-ADG790EBZ | BOARD EVALUATION ADG790 |
| S1210R-331K | INDUCTOR SHIELDED .33UH SMD |
| VI-B6X-EX | CONVERTER MOD DC/DC 5.2V 75W |
| RSC05DRYS-S93 | CONN EDGECARD 10POS DIP .100 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD5232SDZ | 功能描述:BOARD EVAL FOR AD5232 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-AD5232-SDZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:Nonvolatile Memory,Dual 256-Position Digital Potentiometer |
| EVAL-AD5233SDZ | 功能描述:BOARD EVAL FOR AD5233 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-AD5235EBZ | 制造商:Analog Devices 功能描述:EVALUATION BOARD FOR 1024-POSITION DIGITAL POTENTIOMETER 制造商:Analog Devices 功能描述:EVAL BD FOR 1024-POSITION DGTL POTENTIOMETER - Bulk |
| EVAL-AD5235SDZ | 功能描述:BOARD EVAL FOR AD5235 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
發布緊急采購，3分鐘左右您將得到回復。