- 您現在的位置：買賣IC網 > PDF目錄97935 > EV6040 EvKit for FX604 and FX614 PDF資料下載
參數資料
| 型號： | EV6040 |
| 英文描述： | EvKit for FX604 and FX614 |
| 中文描述： | 評估板的FX604和FX614 |
| 文件頁數： | 9/13頁 |
| 文件大小： | 899K |
| 代理商： | EV6040 |
Evaluation Kit User Manual for FX604
EV6040
1996 Consumer Microcircuits Limited
5
UM6040/3
1.3
Quick Start
This section provides instructions for users who wish to experiment immediately with the evaluation
kit. A fuller description of the kit and its use appears later in this document.
1.3.1
Setting-Up
THE EV6040 COMES PRE-CONFIGURED WITH AN FX604, SET FOR OPERATION AT 5.0V.
The board should be interconnected to a suitable
C control board with a 20-way flat cable, as shown
in the Block Diagram of Figure 1. If the EV6000
C board is not used, then power will need to be
applied separately to the EV6040 evaluation kit through connector J3. An RJ11 (US style) phone jack
is provided for telephone line simulator connection. No board adjustments are required by the user,
although a (
≈ 600) line termination will need to be fitted to R20 before the EV6040 kit can be used.
Other, telco-specific, components may be added, as required.
BEFORE APPLYING POWER, PLEASE CHECK THE FOLLOWING:
When using the EV6040 board with the EV6000
C board, it will be noted that each board has
connections for a single 8 - 35V dc power supply. Only one board needs to be connected as power is
supplied to the other board over the flat cable. Each board has its own power supply regulator chip,
with a jumper to select 3.3V or 5.0V (default ) operation.
MAKE SURE BOTH BOARDS HAVE THIS JUMPER SET TO THE SAME VOLTAGE. DAMAGE
MAY RESULT IF THIS STEP IS NOT OBSERVED. DO NOT OPERATE EITHER BOARD WITH
ITS VOLTAGE SELECTION JUMPER REMOVED.
Ensure the component value jumpers on the evaluation board are correctly set for 3.3V or 5.0V
operation. Please refer to Section 1.6.1.5 for further details.
1.3.2
Operation
This evaluation kit has no inherent functionality without a
C control board and appropriate firmware.
The evaluation board may be used independently of the
C board, if the user wishes to interface to a
different type of
C.
相關PDF資料 |
PDF描述 |
|---|---|
| EV6090 | EvKit for CMX639 |
| EVB3011 | 1 GHz Quadrature Modulator |
| EVB3013A | W3013 Indirect Quadrature Modulator with Gain Control |
| EVB3020A | GSM Multiband RF Transceiver |
| EVB3020A-IFBD | GSM Multiband RF Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EV6090 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EvKit for CMX639 |
| EV60-S1 | 制造商:Cooper Crouse-Hinds 功能描述: |
| EV61-100-11-SERIES | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
| EV61-100-12-SERIES | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
| EV61-100-21-SERIES | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
發布緊急采購，3分鐘左右您將得到回復。