- 您現在的位置：買賣IC網 > PDF目錄4460 > EP4CGX30BF14I7 (Altera)IC CYCLONE IV GX FPGA 30K 169FBG PDF資料下載
參數資料
| 型號： | EP4CGX30BF14I7 |
| 廠商： | Altera |
| 文件頁數： | 18/42頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CYCLONE IV GX FPGA 30K 169FBG |
| 產品培訓模塊： | Cyclone IV FPGA Family Overview |
| 特色產品： | Cyclone? IV FPGAs |
| 標準包裝： | 119 |
| 系列： | CYCLONE® IV GX |
| LAB/CLB數： | 1840 |
| 邏輯元件/單元數： | 29440 |
| RAM 位總計： | 1105920 |
| 輸入/輸出數： | 72 |
| 電源電壓： | 1.16 V ~ 1.24 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | -40°C ~ 100°C |
| 封裝/外殼： | 169-LBGA |
| 供應商設備封裝： | 169-FBGA（14x14） |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
Chapter 1: Cyclone IV Device Datasheet
1–25
Switching Characteristics
December 2013
Altera Corporation
tDLOCK
Time required to lock dynamically (after switchover,
reconfiguring any non-post-scale counters/delays or
areset
is deasserted)
——
1
ms
tOUTJITTER_PERIOD_DEDCLK (6)
Dedicated clock output period jitter
FOUT 100 MHz
—
300
ps
FOUT < 100 MHz
—
30
mUI
tOUTJITTER_CCJ_DEDCLK (6)
Dedicated clock output cycle-to-cycle jitter
FOUT 100 MHz
—
300
ps
FOUT < 100 MHz
—
30
mUI
tOUTJITTER_PERIOD_IO (6)
Regular I/O period jitter
FOUT 100 MHz
—
650
ps
FOUT < 100 MHz
—
75
mUI
tOUTJITTER_CCJ_IO (6)
Regular I/O cycle-to-cycle jitter
FOUT 100 MHz
—
650
ps
FOUT < 100 MHz
—
75
mUI
tPLL_PSERR
Accuracy of PLL phase shift
—
±50
ps
tARESET
Minimum pulse width on areset signal.
10
—
ns
tCONFIGPLL
Time required to reconfigure scan chains for PLLs
—
3.5 (7)
—
SCANCLK
cycles
fSCANCLK
scanclk
frequency
—
100
MHz
tCASC_OUTJITTER_PERIOD_DEDCLK
Period jitter for dedicated clock output in cascaded
PLLs (FOUT 100 MHz)
—
425
ps
Period jitter for dedicated clock output in cascaded
PLLs (FOUT 100 MHz)
—
42.5
mUI
Notes to Table 1–25:
(1) This table is applicable for general purpose PLLs and multipurpose PLLs.
(2) You must connect VCCD_PLL to VCCINT through the decoupling capacitor and ferrite bead.
(3) This parameter is limited in the Quartus II software by the I/O maximum frequency. The maximum I/O frequency is different for each I/O
standard.
(4) The VCO frequency reported by the Quartus II software in the PLL Summary section of the compilation report takes into consideration the VCO
post-scale counter K value. Therefore, if the counter K has a value of 2, the frequency reported can be lower than the fVCO specification.
(5) A high input jitter directly affects the PLL output jitter. To have low PLL output clock jitter, you must provide a clean clock source that is less
than 200 ps.
(6) Peak-to-peak jitter with a probability level of 10–12 (14 sigma, 99.99999999974404% confidence level). The output jitter specification applies
to the intrinsic jitter of the PLL when an input jitter of 30 ps is applied.
(7) With 100-MHz scanclk frequency.
(8) The cascaded PLLs specification is applicable only with the following conditions:
■ Upstream PLL—0.59 MHz Upstream PLL bandwidth < 1 MHz
■ Downstream PLL—Downstream PLL bandwidth > 2 MHz
(9) PLL cascading is not supported for transceiver applications.
Table 1–25. PLL Specifications for Cyclone IV Devices (1), (2) (Part 2 of 2)
Symbol
Parameter
Min
Typ
Max
Unit
發布緊急采購，3分鐘左右您將得到回復。