參數資料
型號: EP20K60ETI144-3ES
元件分類: 電源監測
英文描述: Dual Voltage Monitor with Intergrated CPU Supervisor
中文描述: 雙電壓監視器集成CPU監控
文件頁數: 44/114頁
文件大?。?/td> 1623K
代理商: EP20K60ETI144-3ES
Altera Corporation
35
APEX 20K Programmable Logic Device Family Data Sheet
Figure 23. APEX 20KE CAM Block Diagram
CAM can be used in any application requiring high-speed searches, such
as networking, communications, data compression, and cache
management.
The APEX 20KE on-chip CAM provides faster system performance than
traditional discrete CAM. Integrating CAM and logic into the APEX 20KE
device eliminates off-chip and on-chip delays, improving system
performance.
When in CAM mode, the ESB implements 32-word, 32-bit CAM. Wider or
deeper CAM can be implemented by combining multiple CAMs with
some ancillary logic implemented in LEs. The Quartus II software
combines ESBs and LEs automatically to create larger CAMs.
CAM supports writing “don’t care” bits into words of the memory. The
“don’t-care” bit can be used as a mask for CAM comparisons; any bit set
to “don’t-care” has no effect on matches.
The output of the CAM can be encoded or unencoded. When encoded, the
ESB outputs an encoded address of the data’s location. For instance, if the
data is located in address 12, the ESB output is 12. When unencoded, the
ESB uses its 16 outputs to show the location of the data over two clock
cycles. In this case, if the data is located in address 12, the 12th output line
goes high. When using unencoded outputs, two clock cycles are required
to read the output because a 16-bit output bus is used to show the status
of 32 words.
The encoded output is better suited for designs that ensure duplicate data
is not written into the CAM. If duplicate data is written into two locations,
the CAM’s output will be incorrect. If the CAM may contain duplicate
data, the unencoded output is a better solution; CAM with unencoded
outputs can distinguish multiple data locations.
CAM can be pre-loaded with data during configuration, or it can be
written during system operation. In most cases, two clock cycles are
required to write each word into CAM. When “don’t-care” bits are used,
a third clock cycle is required.
wraddress[]
data[]
wren
inclock
inclocken
inaclr
data_address[]
match
outclock
outclocken
outaclr
相關PDF資料
PDF描述
EP20K100ERI208-1ES Single Digitally Controlled Potentiometer (XDCP™); Temperature Range: -40°C to 85°C; Package: 8-MSOP
EP20K100ERI208-2ES Single Digitally Controlled Potentiometer (XDCP™); Temperature Range: -40°C to 85°C; Package: 8-MSOP
EP20K100ERI208-3ES FPGA
EP20K100ERI240-1ES FPGA
EP20K100ERI240-2ES FPGA
相關代理商/技術參數
參數描述
EP2101-7R 制造商:Power-One 功能描述:DC/DC PS DUAL-OUT 3.3V/5.1V 20A/18A 91W 15PIN - Bulk
EP2101-9R 功能描述:EURO-CASSETTE 110W 3.3V + 5.1V RoHS:否 類別:電源 - 外部/內部(非板載) >> DC DC Converters 系列:* 標準包裝:1 系列:Quint 類型:隔離 輸入電壓:24V 輸出:24V 輸出數:1 輸出 - 1 @ 電流(最大):24 VDC @ 50A 輸出 - 2 @ 電流(最大):- 輸出 - 3 @ 電流(最大):- 輸出 - 4 @ 電流(最大):- 功率(瓦特):1200W 安裝類型:底座安裝 工作溫度:0°C ~ 40°C 效率:- 封裝/外殼:模塊 尺寸/尺寸:4.33" L x 9.09" W x 6.14" H(110mm x 231mm x 156mm) 包裝:散裝 電源(瓦特)- 最大:1200W 批準:- 其它名稱:277-69722866365-NDQUINT-BAT/24DC/12AH
EP21-6.9KOHMS.1PCT 制造商: 功能描述: 制造商:undefined 功能描述:
EP21FPD1ABE 制造商:ITT 制造商全稱:ITT Industries 功能描述:Sealed Tiny Pushbutton Switches
EP21FPD1AKE 制造商:ITT 制造商全稱:ITT Industries 功能描述:Sealed Tiny Pushbutton Switches