• <tt id="gja5j"><nobr id="gja5j"><strike id="gja5j"></strike></nobr></tt>
    <code id="gja5j"><form id="gja5j"><sup id="gja5j"></sup></form></code>
  • <code id="gja5j"><form id="gja5j"><div id="gja5j"></div></form></code>
    參數資料
    型號: EN29F040-90P
    廠商: Electronic Theatre Controls, Inc.
    英文描述: 4 Megabit (512K x 8-bit) Flash Memory
    中文描述: 4兆位(為512k × 8位)閃存
    文件頁數: 11/32頁
    文件大?。?/td> 223K
    代理商: EN29F040-90P
    4800 Great America Parkway, Suite 202
    Santa Clara, CA 95054
    Tel: 408-235-8680
    Fax: 408-235-8685
    11
    EN29F040
    Rev. D, Issue Date: 2001/07/05
    WRITE OPERATION STATUS
    DQ7
    DATA
    Polling
    The EN29F040 provides
    DATA
    Polling on DQ7 to indicate to the host system the status of the
    embedded operations. The
    DATA
    Polling feature is active during the Byte Programming, Sector
    Erase, Chip Erase, and Erase Suspend. (See Table 6)
    When the Byte Programming is in progress, an attempt to read the device will produce the
    complement of the data last written to DQ7. Upon the completion of the Byte Programming, an
    attempt to read the device will produce the true data last written to DQ7. For the Byte Programming,
    DATA
    polling is valid after the rising edge of the fourth
    WE
    or
    CE
    pulse in the four-cycle sequence.
    When the embedded Erase is in progress, an attempt
    to read the device will produce a “0” at the
    DQ7 output. Upon the completion of the embedded Erase, the device will produce the “1” at the DQ7
    output during the read. For Chip Erase, the
    DATA
    polling is valid after the rising edge of the sixth
    W E
    or
    CE
    pulse in the six-cycle sequence. For Sector Erase,
    DATA
    polling is valid after the last
    rising edge of the sector erase
    W E
    or
    CE
    pulse.
    DATA
    Polling must be performed at any address within a sector that is being programmed or erased
    and not a protected sector. Otherwise,
    DATA
    polling may give an inaccurate result if the address
    used is in a protected sector.
    Just prior to the completion of the embedded operations, DQ7 may change asynchronously when the
    output enable (
    OE
    ) is low. This means that the device is driving status information on DQ7 at one
    instant of time and valid data at the next instant of time. Depending on when the system samples the
    DQ7 output, it may read the status of valid data. Even if the device has completed the embedded
    operations and DQ7 has a valid data, the data output on DQ0-DQ6 may be still invalid. The valid
    data on DQ0-DQ7 will be read on the subsequent read attempts.
    The flowchart for
    DATA
    Polling (DQ7) is shown on Flowchart 5. The
    DATA
    Polling (DQ7) timing
    diagram is shown in Figure 8.
    DQ6
    Toggle Bit I
    The EN29F040 provides a “Toggle Bit” on DQ6 to indicate to the host system the status of the
    embedded programming and erase operations. (See Table 6)
    During an embedded Program or Erase operation, successive attempts to read data from the device
    at any address (by toggling
    OE
    or
    CE
    ) will result in DQ6 toggling between “zero” and “one”. Once
    the embedded Program or Erase operation is complete, DQ6 will stop toggling and valid data will be
    read on the next successive attempts. During Byte Programming, the Toggle Bit is valid after the
    rising edge of the fourth
    WE
    pulse in the four-cycle sequence. For Chip Erase, the Toggle Bit is valid
    after the rising edge of the sixth-cycle sequence. For Sector Erase, the Toggle Bit is valid after the
    last rising edge of the Sector Erase
    W E
    pulse. The Toggle Bit is also active during the sector erase
    time-out window.
    相關PDF資料
    PDF描述
    EN29F040-90PI 4 Megabit (512K x 8-bit) Flash Memory
    EN29F040-90T 4 Megabit (512K x 8-bit) Flash Memory
    EN29F040-90TI 4 Megabit (512K x 8-bit) Flash Memory
    ENH050Q1-650 ENH050Q1-650 COLOR THT-LCD MODULE FEATURES
    ENN6612B Electret Condenser Microphone Applications
    相關代理商/技術參數
    參數描述
    EN29F040-90PI 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4 Megabit (512K x 8-bit) Flash Memory
    EN29F040-90T 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4 Megabit (512K x 8-bit) Flash Memory
    EN29F040-90TI 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4 Megabit (512K x 8-bit) Flash Memory
    EN29F040A 制造商:EON 制造商全稱:Eon Silicon Solution Inc. 功能描述:4 Megabit (512K x 8-bit) Flash Memory
    EN29F040A-45JC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4 Megabit (512K x 8-bit) Flash Memory