參數資料
型號： EM2420DK
廠商： Electronic Theatre Controls, Inc.
英文描述： 2.4 GHz IEEE 802.15.4 / ZigBee RF Transceiver
中文描述： 2.4 GHz IEEE 802.15.4標準/ ZigBee的射頻收發器
文件頁數： 38/89頁
文件大?。?/td> 1758K
代理商： EM2420DK
EM2420
Ember Part Number: 120-0049-000
C
EM2420 Datasheet
Page 38 of 89
Clear Channel Assessment section on
page 50 for details on
CCA
.
The preamble sequence is started 12
symbol periods after the command strobe.
After the programmable start of frame
delimiter has been transmitted, data is
fetched from the TXFIFO.
A TXFIFO underflow is issued if too few
bytes
are
written
Transmission
is
stopped. The underflow is indicated in the
TX_UNDERFLOW
status bit, which is
returned during each address byte and
each byte written to the TXFIFO. The
underflow bit is only cleared by issuing a
SFLUSHTX
command strobe.
to
the
automatically
TXFIFO.
then
The TXFIFO can only contain one data
frame at a given time.
After complete transmission of a data
frame, the TXFIFO is automatically refilled
with the last transmitted frame. Issuing a
new
STXON
or
STXONCCA
command
strobe will then cause the
EM2420
to
retransmit the last frame.
Writing to the TXFIFO after a frame has
been transmitted will cause the TXFIFO to
be automatically flushed before the new
byte is written. The only exception is if a
TXFIFO underflow has occurred, when a
SFLUSHTX
command strobe is required.
Buffered receive mode
In buffered receive mode (RX_MODE 0),
the 128 byte RXFIFO, located in the
EM2420
RAM, is used to buffer data
received by the demodulator. Accessing
data in the RXFIFO is described in the
FIFO access section on page 29.
The
FIFO
and
FIFOP
pins are used to
assist the microcontroller in supervising
the RXFIFO. Please note that the
FIFO
and
FIFOP
pins are only related to the
RXFIFO, even if the
EM2420
is in transmit
mode.
Multiple data frames may be in the
RXFIFO simultaneously, as long as the
total number of bytes does not exceed
128.
See the RXFIFO overflow section on page
31 for details on how a RXFIFO overflow
is detected and signaled.
Unbuffered, serial mode
Unbuffered mode should be used for
evaluation / debugging purposes only.
Buffered mode is recommended for all
applications.
In un-buffered mode, the
FIFO
and
FIFOP
pins are reconfigured as data and data
clock pins. The TXFIFO and RXFIFO
buffers are not used in this mode. A
synchronous data clock is provided by the
EM2420
at the
FIFOP
pin, and the
FIFO
pin is used as data input/output. The
FIFOP
clock frequency is 250 kHz when
active. This is illustrated in Figure 20.
In
(
MDMCTRL1.TX_MODE
=1),
synchronization sequence is inserted at
the start of each frame by hardware, as in
buffered mode. Data is sampled by the
EM2420
on the positive edge of
FIFOP
and
should be updated by the microcontroller
on the negative edge of
FIFOP
. See
Figure 20 for an illustration of the timing in
serial transmit mode. The
SFD
and
CCA
pins retain their normal operation also in
serial mode. The
EM2420
will remain in
serial transmit mode until transmission is
turned off manually.
serial
transmit
mode
a
In
(
MDMCTRL1.RX_MODE
=1)
synchronization is still performed by the
EM2420
. This means that the
FIFOP
clock
pin will remain idle low until a start of
frame delimiter has been detected.
serial
receive
mode
byte
相關PDF資料
PDF描述
EM2420EK 2.4 GHz IEEE 802.15.4 / ZigBee RF Transceiver
EM2420TR 2.4 GHz IEEE 802.15.4 / ZigBee RF Transceiver
EM3-DINAV23CO Energy Management Energy Meter with plug-in Output Modules
EM3-DINAV23CR Energy Management Energy Meter with plug-in Output Modules
EM3-DINAV23CX Energy Management Energy Meter with plug-in Output Modules
相關代理商/技術參數
參數描述
EM2420EK 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2.4 GHz IEEE 802.15.4 / ZigBee RF Transceiver
EM2420-RTB 功能描述:IC RF TXRX ZIGBEE 2.4GHZ 48-QLP RoHS:是 類別:RF/IF 和 RFID >> RF 收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:30 系列:- 頻率:4.9GHz ~ 5.9GHz 數據傳輸率 - 最大:54Mbps 調制或協議:* 應用:* 功率 - 輸出:-3dBm 靈敏度:- 電源電壓:2.7 V ~ 3.6 V 電流 - 接收:* 電流 - 傳輸:* 數據接口:PCB，表面貼裝 存儲容量:- 天線連接器:PCB，表面貼裝 工作溫度:-25°C ~ 85°C 封裝/外殼:68-TQFN 裸露焊盤 包裝:管件
EM2420-RTR 功能描述:IC RF TXRX ZIGBEE 2.4GHZ 48-QLP RoHS:是 類別:RF/IF 和 RFID >> RF 收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:30 系列:- 頻率:4.9GHz ~ 5.9GHz 數據傳輸率 - 最大:54Mbps 調制或協議:* 應用:* 功率 - 輸出:-3dBm 靈敏度:- 電源電壓:2.7 V ~ 3.6 V 電流 - 接收:* 電流 - 傳輸:* 數據接口:PCB，表面貼裝 存儲容量:- 天線連接器:PCB，表面貼裝 工作溫度:-25°C ~ 85°C 封裝/外殼:68-TQFN 裸露焊盤 包裝:管件
EM2420-STB 功能描述:IC RF TXRX ZIGBEE 2.4GHZ 48-QLP RoHS:否 類別:RF/IF 和 RFID >> RF 收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:30 系列:- 頻率:4.9GHz ~ 5.9GHz 數據傳輸率 - 最大:54Mbps 調制或協議:* 應用:* 功率 - 輸出:-3dBm 靈敏度:- 電源電壓:2.7 V ~ 3.6 V 電流 - 接收:* 電流 - 傳輸:* 數據接口:PCB，表面貼裝 存儲容量:- 天線連接器:PCB，表面貼裝 工作溫度:-25°C ~ 85°C 封裝/外殼:68-TQFN 裸露焊盤 包裝:管件
EM2420-STR 功能描述:IC RF TXRX ZIGBEE 2.4GHZ 48-QLP RoHS:否 類別:RF/IF 和 RFID >> RF 收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:30 系列:- 頻率:4.9GHz ~ 5.9GHz 數據傳輸率 - 最大:54Mbps 調制或協議:* 應用:* 功率 - 輸出:-3dBm 靈敏度:- 電源電壓:2.7 V ~ 3.6 V 電流 - 接收:* 電流 - 傳輸:* 數據接口:PCB，表面貼裝 存儲容量:- 天線連接器:PCB，表面貼裝 工作溫度:-25°C ~ 85°C 封裝/外殼:68-TQFN 裸露焊盤 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*