- 您現在的位置：買賣IC網 > PDF目錄384287 > ELM337P (Electronic Theatre Controls, Inc.) LIGHT SWITCH PDF資料下載
參數資料
| 型號： | ELM337P |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | LIGHT SWITCH |
| 中文描述： | 燈開關 |
| 文件頁數： | 4/4頁 |
| 文件大?。?/td> | 27K |
| 代理商： | ELM337P |
Example Applications
4 of 4
Figure 1 at right shows the ELM337 installed in a
typical lighting control circuit. The mode has been set to
111 (or HHH), resulting in delays of 10 minutes when
recognizing a light or dark condition. In this case, only
the ‘Dark’ output (pin 6) is used to enable (and disable) a
lighting circuit, but other variations on this theme might
use the Light output (pin 7), or possibly use mode 110 to
provide short (50 msec) output pulses to trigger other
circuits.
The threshold setting resistor (22k
in Figure 1) is
chosen depending on what resistance it is desired to
have the transitions to light or dark occur at. Using the
typical Schmitt voltage thresholds for a 5 volt supply, it
can be shown that the two resistances that switching will
occur at are 1.33R
T
(light to dark) and 0.37R
T
(dark to
light), where R
T
is the threshold setting resistance. For
the 22k
shown, these would be at about 30k
and
8k
, respectively. The values that you choose would
depend on the LDR used, and your application.
If the LDR (R
λ
) is mounted more than a few feet
from the ELM337, the increased exposure could cause
problems due to induced voltages and currents. To
provide protection from these, a resistor (R
prot
) should be
added in series with pin 5 as shown at right. Typically
this resistor would be equal in value to the threshold
setting resistor.
ELM337
ELM337DSA
< http://www.elmelectronics.com/ >Figure 1. Yard Lighting Controller
Figure 2. Time Delay Dropout Switch
The ELM337 is also capable of operating simply as
a delay circuit. By hard-wiring the mode pins for a
desired delay, and applying logic levels to the LDR pin,
symmetrical output delays of up to 10 minutes can be
obtained.
Asymmetrical delays can also be obtained as shown
in Figure 2. This circuit connects the ELM337 to provide
a 50msec delay on pickup and 10 second time delay on
dropout function.
Operation of the circuit can best be explained as
follows. When the ‘start’ pushbutton is pressed, the M2
and M1 pins will both be at a logic low level, while M0 will
be high. The LDR input is also at a low level, simulating
an LDR that is just ‘seeing’ light. Since the mode is 001
or LLH, then from Table 1 (on page 2) the Light output
will go to a high level after 50msec. This delay is
desirable as it ensures that the input is legitimate by
providing some degree of switch debouncing.
As soon as the pushbutton is released, the M2
mode pin returns to a high level, and what appears to be
a dark input will be on the LDR pin. From Table 1, with
mode 101, the output will turn off after 10 seconds.
Certainly several other variations are possible by
connecting the mode pins in different combinations. Why
not try your hand at some…
0.01μF
To the
controlled
circuit
1
2
3
4
8
7
6
5
start
337
+5V
+5V
22K
22K
1
2
3
4
8
7
6
5
+5V
0.01μF
To the
lighting
circuit
R
λ
R
prot
(see text)
R
T
相關PDF資料 |
PDF描述 |
|---|---|
| ELM337SM | LIGHT SWITCH |
| ELM381 | 60 Hz Long Interval Counter |
| ELM413 | LED controller and a circuit startup timer in an 8 pin package |
| ELM446 | 50 HZ GENERATOR |
| ELM446P | 50 HZ GENERATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ELM337SM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LIGHT SWITCH |
| ELM339 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:INFRARED REMOTE CONTROL |
| ELM33905YDL | 功能描述:LED 電路板指示器 Vert LED Assembly 5mm Yellow 585 nm RoHS:否 制造商:Lumex LED 大小:3 mm 照明顏色:Green 波長:565 nm 光強度:30 mcd 安裝類型:SMD/SMT 顯示角:60 deg 封裝:Reel |
| ELM33MM5GD | 功能描述:LED 電路板指示器 Vert LED Assembly 5mm Green 565 nm RoHS:否 制造商:Lumex LED 大小:3 mm 照明顏色:Green 波長:565 nm 光強度:30 mcd 安裝類型:SMD/SMT 顯示角:60 deg 封裝:Reel |
| ELM33MM5SRD | 功能描述:LED 電路板指示器 Vert LED Assembly 5mm Super Red 660 nm RoHS:否 制造商:Lumex LED 大小:3 mm 照明顏色:Green 波長:565 nm 光強度:30 mcd 安裝類型:SMD/SMT 顯示角:60 deg 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。