- 您現在的位置：買賣IC網 > PDF目錄381793 > ELJSA22NKF (Panasonic Corporation) Chip inductors PDF資料下載
參數資料
| 型號： | ELJSA22NKF |
| 廠商： | Panasonic Corporation |
| 英文描述： | Chip inductors |
| 中文描述： | 片式電感器 |
| 文件頁數： | 15/15頁 |
| 文件大?。?/td> | 1386K |
| 代理商： | ELJSA22NKF |
Chip Inductors
Cautions for use
For securing upgraded reliability and safety, consider following caution items.
1. Land pattern design
Refer to the recommended land dimensions of each type at flow and reflow solderings.
Avoid placing the chip inductor on any metal pattern except the land because the drop of Q and mutual
conductance may occur.
Provisions for venting of flux gases should be made for high density assemblies.
2. Mounting
Placement force should not exceed 20N because electric and magnetic characteristics change by applying
strong force.
3. Soldering
a
Flow soldering
Recommended conditions; 260 C max., 5sec. max.(total time at 2 waves method)
b
Reflow soldering
1
Infra-red reflow soldering
Recommended conditions: 200 C or high at electrode, 60sec. max. and peak 250 C max., 5sec. max.
If the solder at the two electrodes are not melt simultaneously, the chip inductor may not be mounted
on the right place.
It is recommended to fix by adhesive when the deviation is great.
2
VPS reflow soldering
Recommended conditions: 215±5 C, 20 to 60sec.
4. Cleaning
1
Do not use acid or alkari agents. Some cleaning solvents out of CFC may damage the products.
Confirm the reliability in advance.
2
If ultrasonic cleaning is employed, please inform us immediately for technical consultation.
5. Instructions for applying current
The rated current is defined as the smaller value of either the current value when the inductance drops
10 % down from the initial point, or the current value when the average temperature of coil inside rises
20 K up from initial point.
Do not operate this coils beyond the specified rated current.
6. Storage
1
Be careful a high temperature, a large amount of moisture, gases and magnetic field.
2
At long storage of more than 1 year, use the products after inspecting the outer structure
相關PDF資料 |
PDF描述 |
|---|---|
| ELJSA22NMF | Chip inductors |
| ELJSA2N2DF | Chip inductors |
| ELJSA2N2JF | Chip inductors |
| ELJSA2N2KF | Chip inductors |
| ELJSA2N2MF | Chip inductors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ELJSA22NMF | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:Chip inductors |
| ELJSA270KF | 制造商:Panasonic Industrial Devices 功能描述: |
| ELJ-SA270KF | 功能描述:固定電感器 27UH 10% SA TYPE INDUCTOR RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| ELJSA271KF | 制造商:Panasonic Industrial Devices 功能描述: 制造商:Panduit Corp 功能描述:Inductor, Wirewound, 270uh, 10±% |
| ELJ-SA271KF | 功能描述:固定電感器 270UH 10% SA TYPE INDUCTOR RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
發布緊急采購，3分鐘左右您將得到回復。