參數資料
| 型號： | EL4332CSZ-T13 |
| 廠商： | Intersil |
| 文件頁數： | 14/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | MUX/AMP TRIPLE 2:1 300MHZ 16SOIC |
| 標準包裝： | 2,500 |
| 應用： | 2:1 多路復用器-放大器 |
| 電路數： | 3 |
| -3db帶寬： | 300MHz |
| 轉換速率： | 650 V/µs |
| 電流 - 電源： | 48mA |
| 電流 - 輸出 / 通道： | 40mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 帶卷 (TR) |
8
Applications Information
Figure 26 shows a typical use for the EL4332. The circuit is a
component video (R,G, B or Y,U,V) multiplexer. Since the
gain of the internal amplifiers has been set to 2, the only
extra components needed are the supply decoupling
capacitors and the back terminating resistors, if transmission
lines are to be driven. The EL4332 can drive backmatched
50
or 75 loads.
Grounds
It will be noticed that each mux-amp channel has its own
separate ground pin. These ground pins have been kept
separate to keep the channel separation inside the chip as
large as possible. The feedback resistors use these ground
pins as their reference. The resistors total 400
, so there is
a significant signal current flowing from these pins to ground.
The ground pins should all be connected together, to a
ground plane underneath the chip. 1 oz. copper for the
ground plane is highly recommended.
Further notes and recommended practices for high speed
printed circuit board layout can be found in the tutorials in
the Elantec databooks.
Supplies
Supply bypassing should be as physically near the power
pins as possible. Chip capacitors should be used to
minimize lead inductance. Note that larger values of
capacitor tend to have larger internal inductances. So when
designing for 3 transmission lines or similar moderate loads,
a 0.1F ceramic capacitor right next to the power pin in
parallel with a 22F tantalum capacitor placed as close to
the 0.1F is recommended. For lighter loadings, or if not all
the channels are being used, a single 4.7F capacitor has
been found quite adequate.
Note that component video signals do tend to have a high
level of signal correlation. This is especially true if the video
signal has been derived from 3 synchronously clocked
DACs. This corresponds to all three channels drawing large
slew currents simultaneously from the supplies. Thus, proper
bypassing is critical.
FIGURE 26. TYPICAL CONNECTION FOR A 2:1 COMPONENT VIDEO MULTIPLEXER
EL4332
相關PDF資料 |
PDF描述 |
|---|---|
| EL4340IU-T7 | MUX/AMP TRIPLE 500MHZ 24-QSOP |
| EL4501IU-T13 | IC VIDEO FRONT END AMP 24-QSOP |
| EL4511CU-T13 | IC SUPER SYNC SEPARATOR 24-QSOP |
| EL4543IL-T7 | IC DRVR TWISTED TRPL DIFF 20-QFN |
| EL4581CS-T13 | IC SYNC SEPARATOR S-H 50% 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EL4332CSZ-T7 | 功能描述:IC MUX-AMP TRPL 300MHZ 16-SOIC RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| EL4340 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:500MHz Triple, Multiplexing Amplifiers |
| EL4340_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:500MHz Triple, Multiplexing Amplifiers |
| EL4340_10 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:500MHz Triple, Multiplexing Amplifiers |
| EL4340IU | 功能描述:IC MUX AMP TRPL 500MHZ 24-QSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。