參數資料
型號: EL2360C
英文描述: Triple 130 MHz Current Feedback Amplifier
中文描述: 三130 MHz電流反饋放大器
文件頁數: 4/16頁
文件大小: 417K
代理商: EL2360C
EL2360C
Triple 130 MHz Current Feedback Amplifier
Applications Information
Contd
Supply Voltage Range and Single Supply
Operation
The EL2360C has been designed to operate with
supply voltages from g2V to g15V Optimum
bandwidth slew rate and video characteristics
are obtained at higher supply voltages However
at g2V supplies the b3 dB bandwidth at AV e
a
2 is a respectable 70 MHz The following figure
is an oscilloscope plot of the EL2360C at g2V
supplies AV ea2 RF e RG e 560X driving a
load of 150
X showing a clean g600 mV signal at
the output
2360 – 11
If a single supply is desired values from a4V to
a
30V can be used as long as the input common
mode range is not exceeded When using a single
supply be sure to either 1) DC bias the inputs at
an appropriate common mode voltage and AC
couple the signal or 2) ensure the driving signal
is within the common mode range of the
EL2360C which is typically 15V from each sup-
ply rail
Settling Characteristics
The EL2360C offers superb settling characteris-
tics to 01% typically in the 35 ns to 40 ns range
There are no aberrations created from the input
stage which often cause longer settling times in
other current feedback amplifiers The EL2360C
is not slew rate limited therefore any size step up
to g10V gives approximately the same settling
time
As can be seen from the Long Term Settling Er-
ror curve for AV ea1 there is approximately a
0035% residual which tails away to 001% in
about 40
ms This is a thermal settling error
caused by a power dissipation differential (before
and after the voltage step) For AV eb1 due to
the inverting mode configuration this tail does
not appear since the input stage does not experi-
ence the large voltage change as in the non-in-
verting mode With AV eb1 001% settling
time is slightly greater than 100 ns
Power Dissipation
The EL2360C amplifier combines both high
speed and large output current capability at a
moderate supply current in very small packages
It is possible to exceed the maximum junction
temperature allowed under certain supply volt-
age temperature and loading conditions To en-
sure that the EL2360C remains within it’s abso-
lute maximum ratings the following discussion
will help to avoid exceeding the maximum junc-
tion temperature
The maximum power dissipation allowed in a
package is determined according to 1
PDMAX e
TJMAX b TAMAX
iJA
1
where
TJMAX e Maximum Junction Temperature
TAMAX e Maximum Ambient Temperature
iJA e Thermal Resistance of the Package
PDMAX e Maximum Power Dissipation
in the Package
The maximum power dissipation actually pro-
duced by an IC is the total quiescent supply cur-
rent times the total power supply voltage plus
the power in the IC due to the load or 2
PDMAX e N (VS ISMAX a (VS bVOUT)
VOUT
RL
)
2
where
N e
Number of amplifiers
VS e
Total Supply Voltage
ISMAX e Maximum Supply Current per ampli-
fier
VOUT e Maximum Output Voltage of the Ap-
plication
RL e
Load Resistance tied to Ground
12
相關PDF資料
PDF描述
EL2360CN Triple 130 MHz Current Feedback Amplifier
EL2360CS Triple 130 MHz Current Feedback Amplifier
EL2386 250 MHz Triple Current Feedback Amp w/Disable
EL2386C 250 MHz Triple Current Feedback Amp w/Disable
EL2386CN 250 MHz Triple Current Feedback Amp w/Disable
相關代理商/技術參數
參數描述
EL2360CN 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple 130MHz Current Feedback Amplifier
EL2360CS 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple 130MHz Current Feedback Amplifier
EL2386 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:250MHz Triple Current Feedback Amplifier with Disable
EL2386C 制造商:ELANTEC 制造商全稱:ELANTEC 功能描述:250 MHz Triple Current Feedback Amp w/Disable
EL2386CN 制造商:ELANTEC 制造商全稱:ELANTEC 功能描述:250 MHz Triple Current Feedback Amp w/Disable