- 您現在的位置：買賣IC網 > PDF目錄97900 > EL2257CS 125 MHz Single Supply, Clamping Op Amps PDF資料下載
參數資料
| 型號： | EL2257CS |
| 元件分類： | 運算放大器 |
| 英文描述： | 125 MHz Single Supply, Clamping Op Amps |
| 中文描述： | 125 MHz的單電源，鉗位運算放大器 |
| 文件頁數： | 6/21頁 |
| 文件大?。?/td> | 1617K |
| 代理商： | EL2257CS |
14
EL2257C/EL2357C
125 MHz Single Supply, Clamping Op Amps
E
L
2257C/E
L2357C
As far as the output stage of the amplifier is concerned,
RF + RG appear in parallel with RL for gains other than
+1. As this combination gets smaller, the bandwidth
falls off. Consequently, RF has a minimum value that
should not be exceeded for optimum performance.
For AV = +1, RF = 0 is optimum. For AV = -1 or +2
(noise gain of 2), optimum response is obtained with RF
between 500
and 1 k. For A
V = -4 or +5 (noise gain
of 5), keep RF between 2 k and 10 k.
Video Performance
For good video performance, an amplifier is required to
maintain the same output impedance and the same fre-
quency response as DC levels are changed at the output.
This can be difficult when driving a standard video load
of 150
, because of the change in output current with
DC level. Differential Gain and Differential Phase for
the EL2257C/EL2357C are specified with the black
level of the output video signal set to +1.2V. This allows
ample room for the sync pulse even in a gain of +2 con-
figuration. This results in dG and dP specifications of
0.05% and 0.05° while driving 150
at a gain of +2.
Setting the black level to other values, although accept-
able, will compromise peak performance. For example,
looking at the single supply dG and dP curves for
RL=150, if the output black level clamp is reduced
fr o m 1 . 2V to 0. 6V dG/dP will inc r e a se f r om
0.05%/0.05° to 0.08%/0.25°. Note that in a gain of +2
configuration, this is the lowest black level allowed such
that the sync tip doesn’t go below 0V.
If your application requires that the output goes to
ground, then the output stage of the EL2257C/EL2357C,
like all other single supply op amps, requires an external
pull down resistor tied to ground. As mentioned above,
the current flowing through this resistor becomes the DC
bias current for the output stage NPN transistor. As this
current approaches zero, the NPN turns off, and dG and
dP will increase. This becomes more critical as the load
resistor is increased in value. While driving a light load,
such as 1 k
, if the input black level is kept above
1.25V, dG and dP are a respectable 0.03% and 0.03°.
For other biasing conditions see the Differential Gain
and Differential Phase vs. Input Voltage curves.
Output Drive Capability
In spite of their moderately low 5 mA of supply current,
the EL2257C/EL2357C are capable of providing ±100
mA of output current into a 10
load, or ±60 mA into
50
. With this large output current capability, a 50
load can be driven to ±3V with VS = ±5V, making it an
excellent choice for driving isolation transformers in
telecommunications applications.
Driving Cables and Capacitive Loads
When used as a cable driver, double termination is
always recommended for reflection-free performance.
For those applications, the back-termination series resis-
tor will de-couple the EL2257C/EL2357C from the
cable and allow extensive capacitive drive. However,
other applications may have high capacitive loads with-
out a back-termination resistor. In these applications, a
small series resistor (usually between 5
and 50) can
be placed in series with the output to eliminate most
peaking. The gain resistor (RG) can then be chosen to
make up for any gain loss which may be created by this
additional resistor at the output.
Disable/Power-Down
Each amplifier in the EL2257C/EL2357C can be indi-
vidually disabled, placing each output in a high-
impedance state. The disable or enable action takes only
about 40 ns. When all amplifiers are disabled, the total
supply current is reduced to 0 mA, thereby eliminating
all power consumption by the EL2257C/EL2357C. The
EL2257C/EL2357C amplifier’s power down can be
controlled by standard CMOS signal levels at each
ENABLE pin. The applied CMOS signal is relative to
the GND pin. For example, if a single +5V supply is
used, the logic voltage levels will be +0.5V and +2.0V.
If using dual ±5V supplies, the logic levels will be -4.5V
and -3.0V. Letting all ENABLE pins float will disable
the EL2257C/EL2357C. If the power-down feature is
not desired, connect all ENABLE pins to the VS+ pin.
The guaranteed logic levels of +0.5V and +2.0V are not
standard TTL levels of +0.8V and +2.0V, so care must
be taken if standard TTL will be used to drive the
ENABLE pins.
相關PDF資料 |
PDF描述 |
|---|---|
| EL2260C | Dual/Quad 130 MHz Current Feedback Amplifiers |
| EL2260CN | Dual/Quad 130 MHz Current Feedback Amplifiers |
| EL2260CS | Dual/Quad 130 MHz Current Feedback Amplifiers |
| EL2260 | 1GHz, 4x1 Multiplexing Amplifier; Temperature Range: -40°C to 85°C; Package: 14-SOIC T&R |
| EL2270CN | 70 MHz/1 mA Current Mode Feedback Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EL2257CS-02 | 制造商:Intersil Corporation 功能描述: |
| EL2257CS-T13 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:125MHz Single Supply, Clamping Op Amp |
| EL2257CS-T7 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:125MHz Single Supply, Clamping Op Amp |
| EL2259 | 制造商:Rittal 功能描述:ENCLOSURE COMBINATION 9U |
| EL2259 | 制造商:Rittal 功能描述:COMBINATION ENCLOSURE 9U |
發布緊急采購，3分鐘左右您將得到回復。