- 您現在的位置：買賣IC網 > PDF目錄17024 > EA-EDU-009 (Embedded Artists)BOARD EDUCATION LPC2103 PDF資料下載
參數資料
| 型號： | EA-EDU-009 |
| 廠商： | Embedded Artists |
| 文件頁數： | 11/37頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EDUCATION LPC2103 |
| 標準包裝： | 1 |
| 類型： | MCU |
| 適用于相關產品： | LPC2103 |
| 所含物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
LPC2101_02_03_4
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 2 June 2009
19 of 37
NXP Semiconductors
LPC2101/02/03
Single-chip 16-bit/32-bit microcontrollers
6.17.4 Code security (Code Read Protection - CRP)
This feature of the LPC2101/02/03 allows user to enable different levels of security in the
system so that access to the on-chip ash and use of the JTAG and ISP can be restricted.
When needed, CRP is invoked by programming a specic pattern into a dedicated ash
location. IAP commands are not affected by the CRP.
Implemented in bootloader code version 2.21 are three levels of the Code Read
Protection:
1. CRP1 disables access to chip via the JTAG and allows partial ash update (excluding
ash sector 0) using a limited set of the ISP commands. This mode is useful when
CRP is required and ash eld updates are needed but all sectors cannot be erased.
2. CRP2 disables access to chip via the JTAG and only allows full ash erase and
update using a reduced set of the ISP commands.
3. Running an application with level CRP3 selected fully disables any access to chip via
the JTAG pins and the ISP. This mode effectively disables ISP override using P0.14
pin, too. It is up to the user’s application to provide (if needed) ash update
mechanism using IAP calls or call reinvoke ISP command to enable ash update via
UART0.
Remark: Parts LPC2101/02/03 Revision ‘-’ have CRP2 enabled only (bootloader code
version 2.2).
6.17.5 External interrupt inputs
The LPC2101/02/03 include up to three edge or level sensitive external interrupt inputs as
selectable pin functions. When the pins are combined, external events can be processed
as three independent interrupt signals. The external interrupt inputs can optionally be
used to wake-up the processor from Power-down mode and Deep power-down mode.
Additionally all 10 capture input pins can also be used as external interrupts without the
option to wake the device up from Power-down mode.
6.17.6 Memory mapping control
The memory mapping control alters the mapping of the interrupt vectors that appear
beginning at address 0x0000 0000. Vectors may be mapped to the bottom of the on-chip
ash memory, or to the on-chip static RAM. This allows code running in different memory
spaces to have control of the interrupts.
6.17.7 Power control
The LPC2101/02/03 supports three reduced power modes: Idle mode, Power-down
mode, and Deep power-down mode.
CAUTION
If level three Code Read Protection (CRP3) is selected, no future factory testing can be
performed on the device.
相關PDF資料 |
PDF描述 |
|---|---|
| 0210490228 | CABLE JUMPER 1.25MM .229M 16POS |
| 0210490227 | CABLE JUMPER 1.25MM .229M 16POS |
| IL13-US1-SVT-3100-183 | LOCKING LINE CORD 3 COND US 6' |
| 0210391015 | CABLE JUMPER 1MM .102M 31POS |
| STD21W-W | WIRE & CABLE MARKERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EA-EDU-010 | 功能描述:開發板和工具包 - ARM LPC2138 EDUCATION BRD RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
| EA-EDU-011 | 功能描述:開發板和工具包 - ARM EXPERIMENT EXPANSION BRD RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
| EA-EL 3160-60 | 制造商:EA ELEKTRO-AUTOMATIK 功能描述:ELECTRONIC LOAD, 160V / 60A, EURO+UK |
| EA-EL 3160-60 | 制造商:EA Electro-Automatik GmbH 功能描述:ELECTRONIC LOAD 160V / 60A |
| EA-EL 3400-25 | 制造商:EA Electro-Automatik GmbH 功能描述:ELECTRONIC LOAD, 400V / 25A, EURO+UK |
發布緊急采購，3分鐘左右您將得到回復。