參數資料
型號： E5551A-DIT
英文描述： Transponder
中文描述： 轉發
文件頁數： 4/21頁
文件大?。?/td> 157K
代理商： E5551A-DIT
e5551
Rev. A2, 19-Apr-00
12 (21)
16 ms
No modulation
Write mode
Check V
HV on
Modulation
Operation
Write
Vpp/Lock ok?
Program EEPROM
READ
0.12 ms
Writing done (> 64 clocks since last gap)
Programming ends
Reading starts
Programming starts
HV on for testing if Vpp is ok
(HV at EEPROMs)
pp
Figure 20. Programming
V
16 ms
Read programming block
Read next block
Programming
with updated modes
Write data into the IC
(e.g., new bitrate)
(= block 0)
Coil 1 – Coil 2
Figure 21. Coil voltage after programming of block 0
Programming
When all necessary information has been written to the
e5551, programming may proceed. There is a 32-clock
delay between the end of writing and the start of pro-
gramming. During this time, Vpp – the EEPROM
programming voltage – is measured and the lock bit for
the block to be programmed is examined. Further, Vpp is
continually monitored throughout the programming
cycle. If at any time Vpp is too low, the chip enters read
mode immediately.
The programming time is 16 ms.
After programming is done, the e5551 enters read mode,
starting with the block just programmed. If either block
or sequence terminators are enabled, the block is pre-
ceded by a block terminator. If the mode register (block 0)
has been reprogrammed, the new mode will be activated
after the just-programmed block has been transmitted
using the previous mode.
Error Handling
Several error conditions can be detected to ensure that
only valid bits are programmed into the EEPROM. There
are two error types which lead to different actions.
Errors During Writing
There are four detectable errors which could occur during
writing data into the e5551:
D Wrong number of field clocks between two gaps
D The OP-code is neither the standard OP-code (’10‘)
nor the stop OP-code (’11‘)
D Password mode is active but the password does not
match the contents of block 7
D The number of bits received is incorrect;
valid bit counts are
D Standard write 38 bits (PWD not set)
D Password write 70 bits (PWD set)
D AOR wake-up 34 bits
D Stop command 2 bits
If any of these four conditions are detected, the IC
starts read mode immediately after leaving write mode.
Reading starts with block 1.
相關PDF資料
PDF描述
E5551A-DOW Transponder
E5551A-FP008 TRANSPONDER|CMOS|SOP|8PIN|PLASTIC
E5552 read/write identification IC with 1 Kbit memory
E5561 e5561 Advance Information [Updated 4/03. 26 Pages] Read/Write transponder IC for contactless RF identification for highly sophisticated security applications.
E629-EDGE629 1 GHz Timing Deskew and Quad Fanout Element
相關代理商/技術參數
參數描述
E5551A-DOW 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Transponder
E5551A-FP008 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSPONDER|CMOS|SOP|8PIN|PLASTIC
E5552 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Transponder
E555423 制造商:Elo Touch Solutions Inc 功能描述:1729L, 17-INCH LCD, CARROLLTOUCH, USB CONTROLLER, GRAY - Bulk
E55556-000 功能描述:電線鑒定 HTCM-SCE-TP-1/2-4H-4 RoHS:否 制造商:TE Connectivity / Q-Cees 產品:Labels and Signs 類型: 材料:Vinyl 顏色:Blue 寬度:0.625 in 長度:1 in
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*