參數資料
型號： E3S-AD11
廠商： Omron Electronics LLC
英文描述： General-Purpose Photoelectric Sensor
中文描述： 通用光電傳感器
文件頁數： 15/18頁
文件大?。?/td> 241K
代理商： E3S-AD11
E3S-A
E3S-A
15
Operation
Photoelectric sensor
Sensing object
Photoelectric sensor
Sensing object
Min
Max
Min
Max
Min
Max
A
B
B
A
OFF
ON
OFF
OFF
ON
OFF
LIGHT
(red)
STABILITY
(green)
LIGHT
(red)
STABILITY
(green)
LIGHT
(red)
STABILITY
(green)
Place target at the desired
sensing distance. Set sensitivity
adjuster to the minimum scale
position, and gradually increase
sensitivity by turning the sensitiv-
ity adjuster clockwise until the
Light Incident indicator (red LED)
turns ON. Position A designates
the point at which the LED has
turned ON.
Remove the target. Starting from
the maximum scale position,
gradually decrease sensitivity by
turning the sensitivity adjuster
counterclockwise until the Light
Incident indicator (red LED) turns
OFF. Position B designates the
point at which the LED has turned
OFF.
Set the sensitivity indicator to the
position between Positions A and
B (in some cases, Positions A
and B are opposite of the above
example). The photoelectric
sensor will then work normally if
the stability indicator (green) is lit
with and without the target. If it
is not lit, stable operation cannot
be expected, in which case a
different detection method should
be applied.
Unlike conventional photoelectric sensors, the variation in the sensitivity of E3S photoelectric sensors is minimal. This means the
sensitivity can be adjusted on only a single photoelectric sensor, and then the adjusters on the other photoelectric sensors can be set
to the same scale position. There is no need to adjust the sensitivity of each photoelectric sensor individually.
Photoelectric sensor
Sensing object
Steps
Step 1
Step 2
Step 3
Function
Determine Position A
Determine Position B
Adjust to optimum setting
Sensing
Condition
Sensitivity
adjuster
Indicators
Procedure
I
SENSITIVITY ADJUSTMENT
I
TIMER AND TURBO SWITCH
E3S Sensors equipped with the self-diagnostic feature incorpo-
rates an OFF-delay timer that can be adjusted within range of 0 to
100 ms.
The emitter of the through-beam sensor with the self-diagnostic
feature incorporates a turbo switch. When this switch is on, the
intensity of the red LED light source can be increased to make a
brighter spot. The OFF-delay time adjuster of the retroreflective
and the 20-cm diffuse reflective sensor is used as a turbo switch.
When the adjuster is pressed, it functions as a turbo switch to
automatically increase the power of the light source to create a
brighter light spot. Do not press the adjuster when turning it.
Turbo Function (Turbo Switch)
With the turbo function switched ON, the light spot is visible even
at a distance of 20 cm (7.87 in), making it easy to check the sensing
position and the angle of the optical axis.
1. After using the turbo function, readjust the OFF-delay time
that had been set, since the OFF-delay time could have
been changed when the turbo switch (which is on the OFF-
delay time adjuster) was pressed.
2. Press the OFF-delay time adjuster to switch ON the turbo
function with a maximum force of 1 kg and within a maximum
period of 3 minutes. (The photoelectric sensor, however, will
not malfunction even if the turbo function is switched on for
more than 3 minutes.)
The turbo function is effective with the turbo switch pressed, and
the function is reset automatically when released.
Normal Operating Condition
Sensitivity adjuster
The OFF-delay
time adjuster is
used as a turbo
switch (black)
With Turbo Switch ON
Visible spot
PUSH
相關PDF資料
PDF描述
E3S-AD12 General-Purpose Photoelectric Sensor
E3S-AD13 General-Purpose Photoelectric Sensor
E3S-AD16 General-Purpose Photoelectric Sensor
E3S-AD17 General-Purpose Photoelectric Sensor
E3S-AD18 General-Purpose Photoelectric Sensor
相關代理商/技術參數
參數描述
E3S-AD11-M1J 0.3M 功能描述:PES, NPN HORIZONTAL MOUNT RoHS:是 類別:傳感器，轉換器 >> 光學 - 反射式 - 邏輯輸出 系列:E3S 標準包裝:1 系列:E3T 檢測距離:* 檢測方法:反射式，背景抑制 物體感測:白色紙 輸出配置:NPN - 開路集電極/亮光 光感測:紅 安裝類型:面板安裝 電流 - 電源:20mA 電源電壓:12 V ~ 24 V 封裝/外殼:模塊，預接線 包裝:散裝 特點:超扁平形 其它名稱:E3T/FL21 2ME3TFL212M
E3SAD11M1J03M 制造商:OMRON AUTOMATION AND SAFETY 功能描述:PES, NPN HORIZONTAL MOUNT 制造商:OMRON Industrial Automation 功能描述:PES, NPN HORIZONTAL MOUNT 制造商:Omron Corporation 功能描述:
E3SAD12 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SENS OPTO REFL 700MM PREWIRE MOD 制造商:Omron Electronic Components LLC 功能描述:Proximity Sensor Photoelectric Light ON/Dark ON NPN 70cm 10V to 30V 3-Pin 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Proximity Sensor Photoelectric Light ON/Dark ON NPN 70cm 10V to 30V 3-Pin
E3S-AD12 功能描述:光電傳感器 70CM DIF NPN HOR RoHS:否 制造商:Omron Industrial 感應方式:Retroreflective 感應距離:2 m 光源:Infrared LED 放大器類型: 連接:Prewired Cable 輸出配置:Light ON
E3SAD13 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SENS OPTO REFL 100MM PREWIRE MOD 制造商:Omron Electronic Components LLC 功能描述:Proximity Sensor Photoelectric Light ON/Dark ON NPN 10cm 10V to 30V 3-Pin 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Proximity Sensor Photoelectric Light ON/Dark ON NPN 10cm 10V to 30V 3-Pin
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*