- 您現在的位置：買賣IC網 > PDF目錄384270 > E3JK (Electronic Theatre Controls, Inc.) Built-in power supply photoelectric sensor PDF資料下載
參數資料
| 型號： | E3JK |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Built-in power supply photoelectric sensor |
| 中文描述： | 內置電源光電傳感器 |
| 文件頁數： | 7/8頁 |
| 文件大小： | 329K |
| 代理商： | E3JK |
A-224
Photoelectric Sensors
Operation
Adjustment
Precautions
Design
Power Reset Time
The Sensor is ready to detect an object within 200 ms after it
is turned ON. If Sensor and load are connected to separate
power supplies, ensure to turn ON the Sensor first.
Wiring Considerations
Connection/Wiring
If the DC transistor output type is used, the sum of load cur-
rents of L-ON output (NO) and D-ON output (NC) should be
within 100 mA. If the sum of load currents exceeds 100 mA,
the load short-circuit protection may be activated. (The load
short-circuit protection is reset by turning OFF the power of
the photoelectric sensor.)
Miscellaneous
Ambient Conditions (Installation Area)
The E3JK will malfunction if installed in the following places.
Places where the E3JK is exposed to a dusty environment.
Places where corrosive gases are produced.
Places where the E3JK is directly exposed to water, oil, or
chemicals.
Item
Through-beam
Retroreflective Models
Diffuse-reflective
Model
E3JK
Swing the receiver and emitter ver-
tically and/or horizontally and set
the adjuster in the center of the
range where the indicator of the re-
ceiver turns ON.
Like the through-beam model, ad-
just the reflector and emitter/re-
ceiver. Since the directional angle
of the emitter/receiver is 1 to 5°, ad-
just the emitter/receiver especially
carefully.
(1) If you have a sensing object as shown in the figure, turn the sensitivity
adjuster clockwise (increase the sensitivity) until the indicator is turned
ON, and define this adjuster position as (A).
(2) Remove the sensing object, turn the sensitivity adjuster clockwise until
the indicator is turned ON by a background object, and define this posi-
tion as (B).
(3) Turn the sensitivity adjuster counterclockwise (decrease the sensitivity)
from (B) until the indicator is turned OFF, and define this position as (C).
(4) The position in the middle of (A) and (C) is the optimum position. If the
indicator is not turned ON by the background object at the maximum
sensitivity, set the adjuster in the middle of (A) and maximum sensitivity.
∑
The sensitivity adjuster may be damaged if an excessive force is applied.
Correct Use
With sensing object
Without sensing object
Operation
Sensitivity
MIN
MAX
Reset
(C)
Operation
MAX
(C)
(A)
(A)
Setting
(B)
B
o
Sensitivity
MIN
MAX
(A)
Sensitivity
MIN
E3JK
Emitter
Receiver
Emitter
Receiver
相關PDF資料 |
PDF描述 |
|---|---|
| E3JK-5M1 | Built-in power supply photoelectric sensor |
| E3JK-5M2 | Built-in power supply photoelectric sensor |
| E3JK-5S3 | Built-in power supply photoelectric sensor |
| E3JK-DS30M1 | Built-in power supply photoelectric sensor |
| E3JK-DS30M2 | Built-in power supply photoelectric sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| E3JK-5DM1 | 功能描述:光電傳感器 RECEIVER forE3JK-5M1 THRU-BEAM RoHS:否 制造商:Omron Industrial 感應方式:Retroreflective 感應距離:2 m 光源:Infrared LED 放大器類型: 連接:Prewired Cable 輸出配置:Light ON |
| E3JK5DM2 2M | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:DETECTOR ONLY FOR E3JK-5M2 |
| E3JK-5DM2 2M | 功能描述:DETECTOR ONLY FOR E3JK-5M2 RoHS:是 類別:傳感器，轉換器 >> 光學 - 光斷續器 - 槽型 - 邏輯輸出 系列:- 產品變化通告:Product Discontinuation 03/Dec/2009 標準包裝:50 系列:OPTOLOGIC® 檢測距離:0.197"（5mm） 檢測方法:可傳導的 輸出配置:NPN - 開路集電極，緩沖器 安裝類型:通孔 電流 - 電源:5mA 電源電壓:4.5 V ~ 16 V 響應時間:70ns 封裝/外殼:PCB 安裝 |
| E3JK-5DM2-N 2M | 功能描述:光電傳感器 Detector only E3JK-5M2 RoHS:否 制造商:Omron Industrial 感應方式:Retroreflective 感應距離:2 m 光源:Infrared LED 放大器類型: 連接:Prewired Cable 輸出配置:Light ON |
| E3JK5DM2N2M | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:DETECTOR ONLY E3JK-5M2 |
發布緊急采購，3分鐘左右您將得到回復。