參數資料
型號: DS89C430-QNL+
廠商: Maxim Integrated Products
文件頁數: 23/46頁
文件大?。?/td> 0K
描述: IC MCU FLASH 16KB 33MHZ 44-PLCC
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 26
系列: 89C
核心處理器: 8051
芯體尺寸: 8-位
速度: 33MHz
連通性: EBI/EMI,SIO,UART/USART
外圍設備: 電源故障復位,WDT
輸入/輸出數: 32
程序存儲器容量: 16KB(16K x 8)
程序存儲器類型: 閃存
RAM 容量: 1K x 8
電壓 - 電源 (Vcc/Vdd): 4.5 V ~ 5.5 V
振蕩器型: 外部
工作溫度: -40°C ~ 85°C
封裝/外殼: 44-LCC(J 形引線)
包裝: 管件
產品目錄頁面: 703 (CN2011-ZH PDF)
DS89C430/DS89C450 Ultra-High-Speed Flash Microcontrollers
3 of 46
Note 1:
Specifications to -40°C are guaranteed by design and not production tested.
Note 2:
All voltages are referenced to ground.
Note 3:
The user should note that this part is tested and guaranteed to operate down to 4.5V (10%) and that VRST (min) is specified below
that point. This indicates that there is a range of voltages [(VMIN to VRST (min)] where the processor's operation is not guaranteed, but
the reset trip point has not been reached. This should not be an issue in most applications, but should be considered when proper
operation must be maintained at all times. For these applications, it may be desirable to use a more accurate external reset.
Note 4:
While the specifications for VPFW and VRST overlap, the design of the hardware makes it so this is not possible. Within the ranges
given, there is guaranteed separation between these two voltages.
Note 5:
Active current is measured with a 33MHz clock source driving XTAL1, VCC = RST = 5.5V. All other pins are disconnected.
Note 6:
Idle mode current is measured with a 33MHz clock source driving XTAL1, VCC = 5.5V, RST at ground. All other pins are
disconnected.
Note 7:
Stop mode is measured with XTAL and RST grounded, VCC = 5.5V. All other pins are disconnected.
Note 8:
RST = 5.5V. This condition mimics the operation of pins in I/O mode.
Note 9:
During a 0-to-1 transition, a one shot drives the ports hard for two clock cycles. This measurement reflects a port pin in transition
mode.
Note 10:
When addressing external memory.
Note 11:
Guaranteed by design.
Note 12:
Ports 1, 2, and 3 source transition current when pulled down externally. The current reaches its maximum at approximately 2V.
Note 13:
RST = 5.5V. Port 0 is floating during reset and when in the logic-high state during I/O mode.
Note 14:
This port is a weak address holding latch in bus mode. Peak current occurs near the input transition point of the holding latch at
approximately 2V.
相關PDF資料
PDF描述
D38999/24WF32PN CONN RCPT 32POS JAM NUT W/PINS
0355240924 1.78MM MALE 9 POS VERT BLUE
D38999/26FD19PA CONN PLUG 19POS STRAIGHT W/PINS
D38999/20FB98JN CONN RCPT 6POS WALL MNT W/SCKT
MS27467E17B8S CONN PLUG 8POS STRAIGHT W/SCKT
相關代理商/技術參數
參數描述
DS89C430-QNL+ 功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS89C430-QNL+ 制造商:Maxim Integrated Products 功能描述:IC 8BIT MCU 8051 33MHZ LCC-44
DS89C440 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Ultra-High-Speed Flash Microcontrollers
DS89C440-ENG 功能描述:IC MCU FLASH 32KB 25MHZ 44-TQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:89C 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C,智能卡,UART/USART,USB 外圍設備:LED,POR,WDT 輸入/輸出數:9 程序存儲器容量:64KB(64K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件
DS89C440-ENL 功能描述:IC MCU FLASH 32KB 33MHZ 44-TQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:89C 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C,智能卡,UART/USART,USB 外圍設備:LED,POR,WDT 輸入/輸出數:9 程序存儲器容量:64KB(64K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件