- 您現在的位置：買賣IC網 > PDF目錄97870 > DS80C320-MCL (MAXIM INTEGRATED PRODUCTS INC) 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PDIP40 PDF資料下載
參數資料
| 型號： | DS80C320-MCL |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Microcontroller |
| 英文描述： | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PDIP40 |
| 封裝： | 0.600 INCH, PLASTIC, DIP-40 |
| 文件頁數： | 33/38頁 |
| 文件大?。?/td> | 694K |
| 代理商： | DS80C320-MCL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁
DS80C320/DS80C323 High-Speed/Low-Power Microcontrollers
4 of 38
PIN DESCRIPTION (continued)
PIN
DIP
PLCC
TQFP
NAME
FUNCTION
30
33
27
ALE
Address Latch-Enable Output. This pin functions as a clock to latch
the external address LSB from the multiplexed address/data bus. This
signal is commonly connected to the latch enable of an external 373
family transparent latch. ALE has a pulse width of 1.5 XTAL1 cycles
and a period of four XTAL1 cycles. ALE is forced high when the
device is in a reset condition.
39
43
37
AD0
38
42
36
AD1
37
41
35
AD2
36
40
34
AD3
35
39
33
AD4
34
38
32
AD5
33
37
31
AD6
32
36
30
AD7
Port 0, Input/Output. Port 0 is the multiplexed address/data bus.
During the time when ALE is high, the LSB of a memory address is
presented. When ALE falls, the port transitions to a bidirectional data
bus. This bus is used to read external ROM and read/write external
RAM memory or peripherals. The Port 0 has no true port latch and
cannot be written directly by software. The reset condition of Port 0 is
high. No pullup resistors are needed.
Port 1, I/O. Port 1 functions as both an 8-bit, bidirectional I/O port and
an alternate functional interface for Timer 2 I/O, new External
Interrupts, and new Serial Port 1. The reset condition of Port 1 is with
all bits at logic 1. In this state, a weak pullup holds the port high. This
condition also serves as an input mode, since any external circuit that
writes to the port will overcome the weak pullup. When software writes
a 0 to any port pin, the device will activate a strong pulldown that
remains on until either a 1 is written or a reset occurs. Writing a 1 after
the port has been at 0 will cause a strong transition driver to turn on,
followed by a weaker sustaining pullup. Once the momentary strong
driver turns off, the port once again becomes the output high (and
input) state. The alternate modes of Port 1 are outlined as follows:
PIN
DIP
PLCC
TQFP
PORT
ALTERNATE
FUNCTION
1
2
40
P1.0
T2
External I/O for
Timer/Counter 2
2
3
41
P1.1
T2EX
Timer/Counter 2
Capture/Reload Trigger
3
4
42
P1.2
RXD1
Serial Port 1 Input
4
5
43
P1.3
TXD1
Serial Port 1 Output
5
6
44
P1.4
INT2
External Interrupt 2
(Positive-Edge Detect)
6
7
1
P1.5
INT3
External Interrupt 3
(Negative-Edge Detect)
7
8
2
P1.6
INT4
External Interrupt 4
(Positive-Edge Detect)
1–8
2–9
40–44,
1–3
P1.0–P1.7
8
9
3
P1.7
INT5
External Interrupt 5
(Negative-Edge Detect)
相關PDF資料 |
PDF描述 |
|---|---|
| DS80C323-ECD | 8-BIT, MROM, 18 MHz, MICROCONTROLLER, PQFP44 |
| DS80C320-QCL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PQCC44 |
| DS80C320-MNL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PDIP40 |
| DS80C320-ECL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PQFP44 |
| DS80C323-QCD | 8-BIT, MROM, 18 MHz, MICROCONTROLLER, PQCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS80C320MCL+ | 制造商:DSC 功能描述: |
| DS80C320-MCL+ | 功能描述:8位微控制器 -MCU High-Speed Low-Power RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| DS80C320-MCR | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide |
| DS80C320-MEL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS80C320-MND | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide |
發布緊急采購，3分鐘左右您將得到回復。