- 您現在的位置：買賣IC網 > PDF目錄97870 > DS80C320-MCG (DALLAS SEMICONDUCTOR) 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PDIP40 PDF資料下載
參數資料
| 型號： | DS80C320-MCG |
| 廠商： | DALLAS SEMICONDUCTOR |
| 元件分類： | Microcontroller |
| 英文描述： | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PDIP40 |
| 封裝： | 0.600 INCH, PLASTIC, DIP-40 |
| 文件頁數： | 7/42頁 |
| 文件大小： | 736K |
| 代理商： | DS80C320-MCG |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
DS80C320/DS80C323
15 of 42
MHz crystal frequency. Note that once the counter chain has reached a conclusion, the optional interrupt
is generated. Regardless of whether the user enables this interrupt, there are then 512 clocks left until a
reset occurs. There are 5 control bits in special function registers that affect the Watchdog Timer and two
status flags that report to the user. The Reset Watchdog Timer bit (WDCON.0) should be asserted prior to
modifying the Watchdog Timer Mode Select bits (WD1, WD0) to avoid corruption of the watchdog
count.
WDIF (WDCON.3) is the interrupt flag that is set when there are 512 clocks remaining until a reset
occurs. WTRF (WDCON.2) is the flag that is set when a Watchdog reset has occurred. This allows the
application software to determine the source of a reset.
Setting the EWT (WDCON.1) bit enables the Watchdog Timer. The bit is protected by Timed Access
discussed below. Setting the RWT (WDCON.0) bit restarts the Watchdog Timer for another full interval.
Application software must set this bit prior to the timeout. As mentioned previously, WD1 and 0
(CKCON .7 and 6) select the timeout. Finally, the Watchdog Interrupt is enabled using EWDI (EIE.4).
INTERRUPTS
The DS80C320/DS80C323 provides 13 sources of interrupt with three priority levels. The Power-fail
Interrupt (PFI), if enabled, always has the highest priority. There are two remaining user selectable
priorities: high and low. If two interrupts that have the same priority occur simultaneously, the natural
precedence given below determines which is a acted upon. Except for the PFI, all interrupts that are new
to the 8051 family have a lower natural priority than the originals.
INTERRUPT PRIORITY Table 5
NAME
DESCRIPTION
VECTOR
NATURAL PRIORITY
OLD/NEW
PFI
Power-fail Intterupt
33h
j
1NEW
INT0
External Interrupt 0
03h
2
OLD
TF0
Timer 0
0Bh
3
OLD
INT1
External Interrupt 1
13h
4
OLD
TF1
Timer 1
1Bh
5
OLD
SCON0
TI0 or RI0 from serial port 0
23h
6
OLD
TF2
Timer 2
2Bh
7
OLD
SCON1
TI1 or RI1 from serial port 1
3Bh
8
NEW
INT2
External Interrupt 2
43h
9
NEW
INT3
External Interrupt 3
4Bh
10
NEW
INT4
External Interrupt 4
53h
11
NEW
INT5
External Interrupt 5
5Bh
12
NEW
WDTI
Watchdog Timeout Interrupt
63h
13
NEW
相關PDF資料 |
PDF描述 |
|---|---|
| DS80C320-QNG | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44 |
| DS80C320-ECG | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP44 |
| DS80C320-FNG | 8-BIT, 25 MHz, MICROCONTROLLER, PQFP44 |
| DS80C320-FCG | 8-BIT, 25 MHz, MICROCONTROLLER, PQFP44 |
| DS80C320QNG | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS80C320MCG+ | 制造商:Maxim Integrated Products 功能描述:DS80C320 8bit microcontroller,25MHz |
| DS80C320-MCG+ | 功能描述:8位微控制器 -MCU High-Speed Low-Power RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| DS80C320-MCL | 功能描述:8位微控制器 -MCU High-Speed Low-Power RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| DS80C320MCL+ | 制造商:DSC 功能描述: |
| DS80C320-MCL+ | 功能描述:8位微控制器 -MCU High-Speed Low-Power RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。