參數資料
型號: DS75U+T&R
廠商: Maxim Integrated
文件頁數: 10/14頁
文件大?。?/td> 183K
描述: IC THERMOMETER/STAT DIG 8-MSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 3,000
功能: 溫度計,恒溫計
傳感器類型: 內部
感應溫度: -55°C ~ 125°C
精確度: ±3°C(最小值)
拓?fù)洌?/td> ADC(三角積分型),比較器,寄存器庫
輸出類型: I²C?/SMBus?
輸出警報: 無
輸出風扇: 無
電源電壓: 2.7 V ~ 5.5 V
工作溫度: -55°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 8-TSSOP,8-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 8-uMAX
包裝: 帶卷 (TR)
DS75
 
10 of 14
Table 6. Fault Tolerance Configuration
F1
F0
CONSECUTIVE OUT-OF-LIMITS
CONVERSIONS TO TRIGGER O.S.
0
0
1
0
1
2
1
0
4
1
1
6
 
REGISTER POINTER
The four DS75 registers each have a unique two-bit pointer designation, which is defined in Table 7.
When reading from or writing to the DS75, the user must point the DS75 to the register that is to be
accessed. When reading from the DS75, once the pointer is set, it will remain pointed at the same register
until it is changed. For example, if the user desires to perform consecutive reads from the temperature
register, then the pointer only has to be set to the temperature register one time, after which all reads will
automatically be from the temperature register until the pointer value is changed. On the other hand,
when writing to the DS75, the pointer value must be refreshed each time a write is performed even if the
same register is being written to twice in a row.
At power-up, the default pointer value is the temperature register so the temperature register can be read
immediately without resetting the pointer.
Changes to the pointer setting are accomplished as described in the 2-WIRE SERIAL DATA BUS section
of this datasheet.
Table 7. POINTER DEFINITION
REGISTER
P1     P0
Temperature
0
0
Configuration
0
1
T
HYST
 
1
0
T
OS
 
1
1
 
 
2-WIRE SERIAL DATA BUS
The DS75 communicates over a standard bi-directional 2-wire serial data bus that consists of a serial
clock (SCL) signal and serial data (SDA) signal. The DS75 interfaces to the bus via the SCL input pin
and open-drain SDA I/O pin. All communication is MSb first.
 
The following terminology is used to describe 2-wire communication:
Master Device: Microprocessor/microcontroller that controls the slave devices on the bus. The master 
device generates the SCL signal and START and STOP conditions.
Slave: All devices on the bus other than the master. The DS75 always functions as a slave. 
Bus Idle or Not Busy: Both SDA and SCL remain high. SDA is held high by a pullup resistor when the 
bus is idle, and SCL must either be forced high by the master (if the SCL output is push-pull) or pulled
high by a pullup resistor (if the SCL output is open-drain).
Transmitter: A device (master or slave) that is sending data on the bus.  
Receiver: A device (master or slave) that is receiving data from the bus. 
相關PDF資料
PDF描述
FAN4010IL6X_F113 IC CURRENT SENSE 0.2% 6MLP
FAN5069EMTCX IC REG DL BCK/LINEAR 16TSSOP
HIP1011BCB-T IC CTRLR HOT PLUG PCI 16-SOIC
HIP1020CK-T IC CTRLR HOT PLUG SOT23-5
HIP6018BCBZ-T IC REG TRPL BCK/LINEAR 24-SOIC
相關代理商/技術參數
參數描述
DS-7604HI-S 制造商:Hikvision USA 功能描述:4-Chnl Hybrid Network DVRVga 1Tb Max 720P Chnl 制造商:HIKVISION 功能描述:4-CHNL HYBRID NETWORK DVR VGA 1TB MAX 720P CHNL
DS-7604NI-SE/P 制造商:Hikvision USA 功能描述:4-Channel Embedded Plug and Play DVR with Built-In 4-Channel PoE Switch 制造商:HIKVISION 功能描述:NVR 4-CHANNEL H264 NO HDD HDMI AND INTEGRATED 4-PORT POE
DS-7608NI-SE/8P 制造商:Hikvision USA 功能描述:8-Channel Embedded Plug and Play DVR with Built-In 8-Channel PoE Switch 制造商:HIKVISION 功能描述:NVR 8-CHANNEL H264 NO HDD HDMI AND INTEGRATED 8-PORT POE
DS760SL-3 功能描述:線性和開關式電源 748W 12V 63.3A FRONT END SLIMLINE RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓(通道 1):20 V 輸出電流(通道 1):40 A 商用/醫用: 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:Rack 長度: 寬度: 高度:
DS760SL-3-001 制造商:Emerson Network Power - Embedded Power 功能描述:12V OUTPUT, 5V STBY, 760W 1U X 1U X 12.67", REVERSE AIR - Bulk