- 您現在的位置：買賣IC網 > PDF目錄97869 > DS75S (MAXIM INTEGRATED PRODUCTS INC) DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | DS75S |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | 0.150 INCH, SOP-8 |
| 文件頁數： | 3/15頁 |
| 文件大?。?/td> | 338K |
| 代理商： | DS75S |
DS75
11 of 14
START Condition: Signal generated by the master to indicate the beginning of a data transfer on the
bus. The master generates a START condition by pulling SDA from high to low while SCL is high (see
Figure 6). A “repeated” START is sometimes used at the end of a data transfer (instead of a STOP) to
indicate that the master will perform another operation.
STOP Condition: Signal generated by the master to indicate the end of a data transfer on the bus. The
master generates a STOP condition by transitioning SDA from low to high while SCL is high (see Figure
6). After the STOP is issued, the master releases the bus to its idle state.
Acknowledge (ACK): When a device (either master or slave) is acting as a receiver, it must generate an
acknowledge (ACK) on the SDA line after receiving every byte of data. The receiving device performs an
ACK by pulling the SDA line low for an entire SCL period (see Figure 6). During the ACK clock cycle,
the transmitting device must release SDA. A variation on the ACK signal is the “not acknowledge”
(NACK). When the master device is acting as a receiver, it uses a NACK instead of an ACK after the last
data byte to indicate that it is finished receiving data. The master indicates a NACK by leaving the SDA
line high during the ACK clock cycle.
Slave Address: Every slave device on the bus has a unique 7-bit address that allows the master to access
that device. The DS75’s 7-bit bus address is 1 0 0 1 A2 A1 A0, where A2, A1 and A0 are user-selectable via
the corresponding input pins. The three address pins allow up to eight DS75s to be multi-dropped on the
same bus.
Address Byte: The control byte is transmitted by the master and consists of the 7-bit slave address plus a
read/write (R/W
) bit (see Figure 7). If the master is going to read data from the slave device then R/W
=
1, and if the master is going to write data to the slave device then R/W
= 0.
Pointer Byte: The pointer byte is used by the master to tell the DS75 which register is going to be
accessed during communication. The six LSbs of the pointer byte (see Figure 8) are always 0 and the two
LSbs correspond to the desired register as shown in Table 7.
Figure 6. START, STOP, AND ACK SIGNALS
Figure 7. ADDRESS BYTE
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
1
0
1
A2
A1
A0
R/W
Figure 8. POINTER BYTE
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
SCL
SDA
START
Condition
STOP
Condition
…
ACK (or NACK)
From Receiver
相關PDF資料 |
PDF描述 |
|---|---|
| DS80C310-QCG | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44 |
| DS80C310-MCG | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PDIP40 |
| DS80C310-ECG | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP44 |
| DS80C320-ENL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PQFP44 |
| DS80C320-ENG | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS75S/T&R | 制造商:Maxim Integrated Products 功能描述:2-WIRE THERMAL WATCHDOG SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC WATCHDOG THERM 2-W 3/5V 8SOIC |
| DS75S/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS75S+ | 功能描述:板上安裝溫度傳感器 Digital RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS75S+/ | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS75S+T&R | 制造商:Maxim Integrated Products 功能描述:DS75 LEAD FREE SO 8 T&R 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 2-WIRE 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG 8-SOIC 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Digital 制造商:Maxim Integrated Products 功能描述:Temp Sensor Digital Serial (2-Wire) SO8 |
發布緊急采購，3分鐘左右您將得到回復。