- 您現在的位置：買賣IC網 > PDF目錄97869 > DS75S (DALLAS SEMICONDUCTOR) DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | DS75S |
| 廠商： | DALLAS SEMICONDUCTOR |
| 元件分類： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | 0.150 INCH, SOIC-8 |
| 文件頁數： | 13/13頁 |
| 文件大?。?/td> | 240K |
| 代理商： | DS75S |
DS75
9 of 13
DATA TRANSFER ON 2–WIRE SERIAL BUS Figure 4
Figure 5 details how data transfer is accomplished on the two–wire bus. Depending upon the state of the
R/W bit, two types of data transfer are possible:
1. Data transfer from a master transmitter to a slave receiver. The first byte transmitted by the
master is the slave address. Next follows a number of data bytes. The slave returns an acknowledge
bit after each received byte.
2. Data transfer from a slave transmitter to a master receiver. The first byte (the slave address) is
transmitted by the master. The slave then returns an acknowledge bit. Next follows a number of data
bytes transmitted by the slave to the master. The master returns an acknowledge bit after all received
bytes other than the last byte. At the end of the last received byte, a ’not acknowledge’ is returned.
The master device generates all of the serial clock pulses and the START and STOP conditions. A
transfer is ended with a STOP condition or with a repeated START condition. Since a repeated
START condition is also the beginning of the next serial transfer, the bus will not be released.
The DS75 may operate in the following two modes:
1. Slave receiver mode: Serial data and clock are received through SDA and SCL. After each byte is
received, an acknowledge bit is transmitted. START and STOP conditions are recognized as the
beginning and end of a serial transfer. Address recognition is performed by hardware after reception
of the slave address and direction bit.
2. Slave transmitter mode: The first byte is received and handled as in the slave receiver mode. How-
ever, in this mode, the direction bit will indicate that the transfer direction is reversed. Serial data is
transmitted on SDA by the DS75 while the serial clock is input on SCL. START and STOP
conditions are recognized as the beginning and end of a serial transfer.
SLAVE ADDRESS
A control byte is the first byte received following the START condition from the master device. The
control byte consists of a four bit control code; for the DS75, this is set as 1001 binary for read and write
operations. The next three bits of the control byte are the device select bits (A2, A1, A0). They are used
by the master device to select which of eight devices are to be accessed. The set bits are in effect the three
least significant bits of the slave address. The last bit of the control byte (R/W) defines the operation to be
performed. When set to a one a read operation is selected, and when set to a zero a write operation is
selected. Following the START condition, the DS75 monitors the SDA bus checking the device type
identifier being transmitted. Upon receiving the 1001 code and appropriate device select bits, the slave
device outputs an acknowledge signal on the SDA line.
相關PDF資料 |
PDF描述 |
|---|---|
| DS75U/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, SQUARE, SURFACE MOUNT |
| DS75U-C12+T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, SQUARE, SURFACE MOUNT |
| DS75U | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, SQUARE, SURFACE MOUNT |
| DS75S | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS80C310-QCG | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS75S/T&R | 制造商:Maxim Integrated Products 功能描述:2-WIRE THERMAL WATCHDOG SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC WATCHDOG THERM 2-W 3/5V 8SOIC |
| DS75S/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS75S+ | 功能描述:板上安裝溫度傳感器 Digital RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS75S+/ | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS75S+T&R | 制造商:Maxim Integrated Products 功能描述:DS75 LEAD FREE SO 8 T&R 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 2-WIRE 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG 8-SOIC 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Digital 制造商:Maxim Integrated Products 功能描述:Temp Sensor Digital Serial (2-Wire) SO8 |
發布緊急采購，3分鐘左右您將得到回復。