參數資料
型號: DS4026S+KCN
廠商: Maxim Integrated Products
文件頁數: 2/14頁
文件大?。?/td> 0K
描述: IC OSC TCXO 26MHZ 16-SOIC
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 45
類型: 溫度 - 補償晶體振蕩器(TCXO)
頻率: 26MHz
電源電壓: 3.135 V ~ 3.465 V
電流 - 電源: 1.5mA
工作溫度: -40°C ~ 85°C
封裝/外殼: 16-SOIC(0.295",7.50mm 寬)
包裝: 管件
供應商設備封裝: 16-SOIC W
安裝類型: 表面貼裝
DS4026
10MHz to 51.84MHz TCXO
10
______________________________________________________________________________________
Read Mode
In the temperature register (see the
Temperature
Register (02h–03h) table), temperature is represented
as a 12-bit code and is accessible at location 02h and
03h. The upper 8 bits are at location 02h and the lower
4 bits are in the upper nibble of the byte at location
03h. Upon power reset, the registers are set to a +25°C
default temperature and the controller starts a tempera-
ture conversion. The temperature register stores new
temperature readings.
The current temperature is loaded into the (user) tem-
perature registers when a valid I2C slave address and
write is received and when a word address is received.
Consequently, if the two temperature registers are read
in individual I2C transactions, it is possible for a tem-
perature conversion to occur between reads, and the
results can be inaccurate. To prevent this from occur-
ring, the registers should be read using a single, multi-
byte read operation (Figure 5). I2C reads do not affect
the internal temperature registers.
I2C Serial Data Bus
The DS4026 supports a bidirectional I2C bus and data
transmission protocol. A device that sends data onto
the bus is defined as a transmitter and a device receiv-
ing data is defined as a receiver. The device that con-
trols the message is called a master. The devices that
are controlled by the master are slaves. The bus must
be controlled by a master device that generates the
serial clock (SCL), controls the bus access, and gener-
ates the START and STOP conditions. The DS4026
operates as a slave on the I2C bus. Connections to the
bus are made through the open-drain I/O lines SDA
and SCL. Within the bus specifications, a standard
mode (100kHz maximum clock rate) and a fast mode
(400kHz maximum clock rate) are defined. The DS4026
works in both modes.
The following bus protocol has been defined (Figure 3):
Data transfer can be initiated only when the bus is
not busy.
Table 1. Register Map
ADDRESS
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
FUNCTION
00
DCOMP
SIGN
FTUNEH
Frequency Tuning High
01
FTUNEL
Frequency Tuning Low
02
SIGN
TREGH
Temperature MSB
03
TREGL
Temperature LSB
STOP
CONDITION
OR REPEATED
START
CONDITION
REPEATED IF MORE BYTES
ARE TRANSFERED
ACK
START
CONDITION
ACK
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
SLAVE ADDRESS
MSB
SCL
SDA
R/W
DIRECTION
BIT
12
6
7
8
9
1
2
8
9
3–7
Figure 3. I2C Data Transfer Overview
相關PDF資料
PDF描述
VI-B7H-MX-B1 CONVERTER MOD DC/DC 52V 75W
M83723/92R1407N CONN PLUG 7POS STRAIGHT W/PINS
AD5206BRZ100 IC DGTL POT 256POS 100K 24SOIC
MS27474T16B6PA CONN RCPT 6POS JAM NUT W/PINS
MS3450W16-9PZ CONN RCPT 4POS WALL MNT W/PINS
相關代理商/技術參數
參數描述
DS4026S-PCNEVKIT 功能描述:時鐘和定時器開發工具 RoHS:否 制造商:Texas Instruments 產品:Evaluation Modules 類型:Clock Conditioners 工具用于評估:LMK04100B 頻率:122.8 MHz 工作電源電壓:3.3 V
DS4026S-QCC 功能描述:TCXO振蕩器 RoHS:否 制造商:AVX 封裝 / 箱體: 頻率:32.768 kHz 頻率穩定性: 負載電容:15 pF 端接類型:SMD/SMT 電源電壓:3 V 尺寸:2.5 mm W x 3.2 mm L x 1 mm H 輸出格式:CMOS 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 封裝:Reel
DS4026S-QCN 功能描述:TCXO振蕩器 RoHS:否 制造商:AVX 封裝 / 箱體: 頻率:32.768 kHz 頻率穩定性: 負載電容:15 pF 端接類型:SMD/SMT 電源電壓:3 V 尺寸:2.5 mm W x 3.2 mm L x 1 mm H 輸出格式:CMOS 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 封裝:Reel
DS4-02P 制造商:Cooper Bussmann 功能描述:TOP SCREW-ON INSERTION BRIDGE, 2 POLE, F - Bulk 制造商:COOPER BUSSMANN 功能描述:TOP SCREW-ON INSERTION BRIDGE, 2 POLE, F
DS402ST 制造商:DYNEX 制造商全稱:Dynex Semiconductor 功能描述:Rectifier Diode