- 您現在的位置：買賣IC網 > PDF目錄9434 > DS4000A0/WBGA (Maxim Integrated Products)IC OSC TCXO 10MHZ 24BGA PDF資料下載
參數資料
| 型號： | DS4000A0/WBGA |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OSC TCXO 10MHZ 24BGA |
| 標準包裝： | 135 |
| 類型： | 溫度 - 補償晶體振蕩器（TCXO） |
| 頻率： | 10MHz |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 電流 - 電源： | 1.5mA |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 24-BBGA |
| 包裝： | 托盤 |
| 供應商設備封裝： | 24-WBGA（11x9） |
| 安裝類型： | 表面貼裝 |
DS4000 Digitally Controlled TCXO
13 of 16
SLAVE ADDRESS
The slave address is the first byte received following the START condition generated by the master device. The
address byte consists of a 7-bit slave address and the R/
W direction bit. The DS4000 slave address is set to
100010A0, where A0 is externally hardwired to a HIGH or LOW state. This allows design flexibility to set the slave’s
address to one of two possible address locations. The last bit following the slave address is the direction bit (R/
W)
and defines the operation to be performed by the master, transmit data (R/
W = 0), or receive data (R/W = 1).
Following the START condition, the DS4000 monitors the SDA bus by checking the slave address being
transmitted. Upon receiving the proper slave address and R/
W bit, the slave device outputs an acknowledge signal
on the SDA line regardless of the operation mode.
The DS4000 can operate in the following two modes:
1) Slave Receiver Mode: Serial data and clock are received through SDA and SCL. After each byte is received,
an acknowledge bit is transmitted. START and STOP conditions are recognized as the beginning and end of a
serial transfer. Address recognition is performed by the hardware after reception of the slave address and
direction bit (Figure 4).
2) Slave Transmitter Mode: The first byte is received and handled as in the slave receiver mode. However, in
this mode, the direction bit indicates that the transfer direction is reversed. Serial data is transmitted on SDA by
the DS4000 while the serial clock is input on SCL. START and STOP conditions are recognized as the
beginning and end of a serial transfer (Figure 5).
Figure 4. Data Write—Slave Receiver Mode
<SLAVE ADDRESS>
R/
W
<DATA ADDRESS>
<DATA (n)>
S
100010A0
0
A
XXXXXXXX
A
XXXXXXXX
A P
S = START
A = ACKNOWLEDGE
P = STOP
Figure 5. Data Read—Slave Transmitter Mode
<SLAVE ADDRESS>
R/W
<DATA (n)>
<DATA (n + 1)>
<DATA (n + 2)>
<DATA (n + X)>
S
100010A0
1
A
XXXXXXXX
A
XXXXXXXX
A
XXXXXXXX
A
XXXXXXXX
A P
S = START
A = ACKNOWLEDGE
P = STOP
A = NOT ACKNOWLEDGE
相關PDF資料 |
PDF描述 |
|---|---|
| MS3451L20-14PY | CONN RCPT 5POS CBL MNT W/PINS |
| M83723/76R14047 | CONN PLUG 4POS STRAIGHT W/PINS |
| VI-BTX-MX-B1 | CONVERTER MOD DC/DC 5.2V 75W |
| VI-B2J-MY-S | CONVERTER MOD DC/DC 36V 50W |
| MS3451L20-14PX | CONN RCPT 5POS CBL MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS4000B | 功能描述:電線導管 DS4000 BASE 10 FT. RoHS:否 制造商:Panduit 類型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 顏色:Light Gray 大小: 最大光束直徑: 抗拉強度: 外部導管寬度:25 mm 外部導管高度:25 mm |
| DS4000C-BK | 功能描述:電線導管 DS4000 COVER MATTE BLACK - 5FT RoHS:否 制造商:Panduit 類型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 顏色:Light Gray 大小: 最大光束直徑: 抗拉強度: 外部導管寬度:25 mm 外部導管高度:25 mm |
| DS4000C-BZ | 功能描述:電線導管 DS4000 COVER METALLIC BRONZE -5FT RoHS:否 制造商:Panduit 類型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 顏色:Light Gray 大小: 最大光束直徑: 抗拉強度: 外部導管寬度:25 mm 外部導管高度:25 mm |
| DS4000C-DG | 功能描述:電線導管 DS4000 CVR DESIGNER GRAY - 5FT RoHS:否 制造商:Panduit 類型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 顏色:Light Gray 大小: 最大光束直徑: 抗拉強度: 外部導管寬度:25 mm 外部導管高度:25 mm |
| DS4000C-DV | 功能描述:電線導管 DS4000 CVR DESIGNER IVORY - 5FT RoHS:否 制造商:Panduit 類型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 顏色:Light Gray 大小: 最大光束直徑: 抗拉強度: 外部導管寬度:25 mm 外部導管高度:25 mm |
發布緊急采購，3分鐘左右您將得到回復。