- 您現在的位置：買賣IC網 > PDF目錄1915 > DS3170+ (Maxim Integrated Products)IC TXRX DS3/E3 100-CSBGA PDF資料下載
參數資料
| 型號： | DS3170+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 216/230頁 |
| 文件大小： | 0K |
| 描述： | IC TXRX DS3/E3 100-CSBGA |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 640 |
| 功能： | 單芯片收發器 |
| 接口： | DS3，E3 |
| 電路數： | 1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 電流 - 電源： | 120mA |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LBGA，CSBGA |
| 供應商設備封裝： | 100-CSBGA（11x11） |
| 包裝： | 托盤 |
| 包括： | DS3 調幀器，E3 調幀器，HDLC 控制器，芯片內 BERT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁當前第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁
DS3170 DS3/E3 Single-Chip Transceiver
86 of 230
The bits C31, C32, and C33 are all overwritten with the calculated payload parity from the previous DS3 frame.
The bits C41, C42, and C43 are all overwritten with the Far-End Block Error (FEBE) bit. The FEBE bit can be
generated automatically or inserted from a register bit. The FEBE bit source is programmable (automatic or
register). If the FEBE bit is generated automatically, it is zero when at least one C-bit parity error has been detected
during the previous frame.
The bits C51, C52, and C53 are overwritten with the path maintenance data link input from the HDLC controller.
Once all of the DS3 overhead bits have been overwritten, the data stream is passed on to error insertion. If frame
generation is disabled, the incoming DS3 signal is passed on to error insertion. Frame generation is programmable
(on or off). Note: P-bit generation may still be performed even if frame generation is disabled.
10.6.5.3
Transmit C-bit DS3 Error Insertion
Error insertion inserts various types of errors into the different DS3 overhead bits. The types of errors that can be
inserted are framing errors, P-bit parity errors, C-bit parity errors, and Far-End Block Error (FEBE) errors.
The framing error insertion mode is programmable (F-bit, M-bit, SEF, or OOMF). An F-bit error is a single subframe
alignment bit (FXY) error. An M-bit error is a single multiframe alignment bit (M1, M2, or M3) error. An SEF error is an
error in all the subframe alignment bits in a subframe (FX1, FX2, FX3, and FX4). An OOMF error is a single multiframe
alignment bit (M1, M2, or M3) error in two consecutive DS3 frames.
A P-bit parity error is generated by is inverting the value of the P-bits (P1 and P2) in a single DS3 frame. P-bit parity
error(s) can be inserted one error at a time, or continuously. The P-bit parity error insertion mode (single or
continuous) is programmable.
A C-bit parity error is generated by is inverting the value of the C31, C32, and C33 bits in a single DS3 frame. C-bit
parity error(s) can be inserted one error at a time, or continuously. The C-bit parity error insertion mode (single or
continuous) is programmable.
A FEBE error is generated by forcing the C41, C42, and C43 bits in a single multiframe to zero. FEBE error(s) can be
inserted one error at a time, or continuously. The FEBE error insertion rate (single or continuous) is programmable.
Each error type (framing, P-bit parity, C-bit parity, or FEBE) has a separate enable. Continuous error insertion
mode inserts errors at every opportunity. Single error insertion mode inserts an error at the next opportunity when
requested.
the framing multi-error modes (SEF or OOMF) insert the indicated number of error(s) at the next
opportunities when requested; i.e., a single request will cause multiple errors to be inserted. The requests can be
initiated by a register bit(TSEI) or by the manual error insertion input (TMEI). The error insertion initiation type
(register or input) is programmable. The insertion of each particular error type is individually enabled. Once all error
insertion has been performed, the data stream is passed on to overhead insertion.
10.6.5.4 Transmit C-bit DS3 Overhead Insertion
Overhead insertion can insert any (or all) of the DS3 overhead bits into the DS3 frame. The DS3 overhead bits X1,
X2, P1, P2, MX, FXY, and CXY can be sourced from the transmit overhead interface (TOHCLK, TOH, TOHEN, and
TOHSOF). The P-bits (P1 and P2) and C31, C32, and C33 bits are received as an error mask (modulo 2 addition of
the input bit and the internally generated bit). The DS3 overhead insertion is fully controlled by the transmit
overhead interface. If the transmit overhead data enable signal (TOHEN) is driven high, then the bit on the transmit
overhead signal (TOH) is inserted into the output data stream. Insertion of bits using the TOH signal overwrites
internal overhead insertion.
10.6.5.5
Transmit C-bit DS3 AIS/Idle Generation
C-bit DS3 AIS/Idle generation overwrites the data stream with AIS or an Idle signal. If transmit Idle is enabled, the
data stream payload is forced to a 1100 pattern with two ones immediately following each DS3 overhead bit. M1,
M2, and M3 bits are overwritten with the values zero, one, and zero (010) respectively. FX1, FX2, FX3, and FX4 bits are
overwritten with the values one, zero, zero, and one (1001) respectively. X1 and X2 are overwritten with 11. And,
P1, P2, C31, C32, and C33 are overwritten with the calculated payload parity from the previous output DS3 frame.
If transmit AIS is enabled, the data stream payload is forced to a 1010 pattern with a one immediately following
each DS3 overhead bit. M1, M2, and M3 bits are overwritten with the values zero, one, and zero (010) respectively.
FX1, FX2, FX3, and FX4 bits are overwritten with the values one, zero, zero, and one (1001) respectively. X1 and X2
are overwritten with 11. P1, P2, C31, C32, and C33 are overwritten with the calculated payload parity from the previous
output DS3 frame. And, CX1, CX2, and CX3 (X ≠ 3) are overwritten with 000. AIS will overwrite a transmit Idle signal.
相關PDF資料 |
PDF描述 |
|---|---|
| DS3172N+ | IC TXRX DS3/E3 DUAL 400-BGA |
| DS3181N+ | IC ATM/PACKET PHY W/LIU 400PBGA |
| DS32512N+ | IC LIU DS3/E3/STS-1 12P 484-BGA |
| DS3254N+ | IC LIU DS3/E3/STS-1 144-CSBGA |
| DS33M33N+ | IC MAPPER ETHERNET 256CSBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS3170_11 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:DS3/E3 Single-Chip Transceiver Single-Chip Transceiver for DS3 and E3 |
| DS3170+ | 功能描述:網絡控制器與處理器 IC DS3/E3 Single-Chip Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS3170DK | 功能描述:網絡開發工具 DS3170 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V |
| DS3170L | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:DS3/E3 Single-Chip Transceiver |
| DS3170LN | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:DS3/E3 Single-Chip Transceiver |
發布緊急采購，3分鐘左右您將得到回復。