- 您現在的位置：買賣IC網 > PDF目錄10656 > DS2480B+T&R (Maxim Integrated Products)IC LINE DRVR W/SENSOR 1-W 8SOIC PDF資料下載
參數資料
| 型號： | DS2480B+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LINE DRVR W/SENSOR 1-W 8SOIC |
| 產品培訓模塊： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 系列： | * |
| 其它名稱： | DS2480B+T&RDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
DS2480B
Maxim Integrated........................................................................................................................................................................................... 18
PULSE WAVEFORMS, DISARMED
The Pulse command can be used to generate a strong pullup to 5V and a 12V programming pulse,
respectively. The duration of the pulse is predefined if the parameter value code of parameter 010
(Programming Pulse Duration) has a value from 000 to 110, and parameter 011 (Strong Pullup Duration)
has a value from 000 to 101 (see Table 4). Figures 7a and 7b show the timing of a pulse with predefined
duration, which should be considered the normal case. If infinite duration is chosen (parameter value code
111), the host must terminate the Pulse command, as shown in Figures 7c and 7d. All versions of Figure 7
assume that bit 1 of the pulse command is 0, i.e., disarmed mode. See the Communication Commands:
Pulse section for more details on possibilities of the Pulse command.
Figure 7a. STRONG PULLUP TO 5V, PREDEFINED DURATION
The processing of a pulse command is essentially the same, regardless if a strong pullup or a
programming pulse is requested. At t1 the host starts sending the pulse command byte. At t2 the DS2480B
has received the command and immediately generates the pulse. The pulse ends at t3 and the DS2480B
sends out the command response byte to inform the host that the command is completed. The idle time
between t1 and t2 is determined by the time to transmit the command byte at the selected baud rate. The
idle time between t3 and t4 is comprised of the time to transmit the response byte, plus the response time
of the host plus the time to transmit the command and/or data to generate the next time slot.
Figure 7b. 12V PROGRAMMING PULSE, PREDEFINED DURATION
A correct programming pulse can only be generated if the 12V programming voltage is available at the
VPP pin of the DS2480B. The rising and falling edges of the programming pulse are actively controlled by
DS2480B. The slew rate is approximately 14V/s and meets the requirements of 1-Wire EPROM
devices.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX967ESA+T | IC COMPARATOR R-R 8-SOIC |
| AD774BKNZ | IC ADC 12BIT W/BUFF REF 28DIP |
| MAX967EUA+T | IC COMPARATOR R-R 8-UMAX |
| LTC1608ACG#PBF | IC A/D CONV 16BIT SAMPLNG 36SSOP |
| MAX932CUA+T | IC COMPARATOR W/REF 8-UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2480S | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Serial 1.Wire Line Driver |
| DS2482-100 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Single-Channel 1-Wire Master |
| DS2482-100_12 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single-Channel 1-Wire Master |
| DS2482-101 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single-Channel 1-Wire Master with Sleep Mode |
| DS2482-101_12 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single-Channel 1-Wire Master with Sleep Mode |
發布緊急采購，3分鐘左右您將得到回復。