參數資料
型號： DS2438Z
英文描述： Smart Battery Monitor
中文描述： 智能電池監視器
文件頁數： 17/29頁
文件大?。?/td> 351K
代理商： DS2438Z
DS2438
17 of 29
1-Wire BUS SYSTEM
The 1-Wire bus is a system which has a single bus master and one or more slaves. The DS2438 behaves
as a slave. The discussion of this bus system is broken down into three topics: hardware configuration,
transaction sequence, and 1-Wire signaling (signal types and timing).
HARDWARE CONFIGURATION
The 1-Wire bus has only a single line by definition; it is important that each device on the bus be able to
drive it at the appropriate time. To facilitate this, each device attached to the 1-Wire bus must have open
drain or 3-state outputs. The 1-Wire port of the DS2438 (DQ pin) is open drain with an internal circuit
equivalent to that shown in Figure 8. A multidrop bus consists of a 1-Wire bus with multiple slaves
attached. The 1-Wire bus requires a pull-up resistor of approximately 5 k
.
HARDWARE CONFIGURATION
Figure 8
The idle state for the 1 wire bus is high. If for any reason a transaction needs to be suspended, the bus
MUST be left in the idle state if the transaction is to resume. Infinite recovery time can occur between
bits so long as the 1-Wire bus is in the inactive (high) state during the recovery period. If this does not
occur and the bus is left low, all components on the bus will be reset. See Wire-1 Reset Pulse Timing
(Figure 9).
TRANSACTION SEQUENCE
The protocol for accessing the DS2438 via the 1-Wire port is as follows:
Initialization
ROM Function Command
Memory Function Command
Transaction/Data
INITIALIZATION
All transactions on the 1-Wire bus begin with an initialization sequence. The initialization sequence
consists of a reset pulse transmitted by the bus master followed by presence pulse(s) transmitted by the
slave(s). The presence pulse lets the bus master know that the DS2438 is on the bus and is ready to
operate. For more details, see the “1-Wire Signaling” section.
相關PDF資料
PDF描述
DS2442 Battery Management
DS2501 1A VERY LOW DROPOUT VOLTAGE REGULATORS
DS2502 1 kbit Add-Only Memory
DS2502P-E48 48-Bit Node Address Chip
DS2502-UN UniqueWare Add-Only Memory
相關代理商/技術參數
參數描述
DS2438Z/T&R 制造商:Maxim Integrated Products 功能描述:SMART BATTERY MONITOR 8-SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MONITOR SMART BATTERY 8-SOIC
DS2438Z/T&R 功能描述:IC MONITOR SMART BATTERY 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT
DS2438Z+ 功能描述:電池管理 Smart Battery Monitor RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
DS2438Z+T&R 制造商:Maxim Integrated Products 功能描述:MONITOR MULTI-CHEM 8SOIC N - Tape and Reel 制造商:Maxim Integrated Products 功能描述:BATT MONITOR 8-SOIC T&R PBFREE 制造商:Maxim Integrated Products 功能描述:IC MONITOR SMART BATTERY 8-SOIC 制造商:Maxim Integrated Products 功能描述:Battery Management Smart Battery Monitor
DS2438Z+T&R 功能描述:電池管理 Smart Battery Monitor RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*