參數資料
型號： DS2438
英文描述： Smart Battery Monitor
中文描述： 智能電池監視器
文件頁數： 10/29頁
文件大?。?/td> 351K
代理商： DS2438
DS2438
10 of 29
Two other time-related functions are available. The first is the Disconnect Timestamp, which is written to
by the DS2438 whenever it senses that the DQ line has been low for approximately 2 seconds. This
condition would signal that the battery pack has been removed from the system; the time when that
occurs is written into the Disconnect Timestamp register, so that upon replacement into the system, the
system can determine how long the device has been in storage, to facilitate self-discharge corrections to
the remaining battery capacity. After the disconnect has been detected, the DS2438 reverts to a sleep
mode, during which nothing is active except the real time clock.
The other timestamp is the End-of-Charge timestamp, which is written to by the DS2438 whenever it
senses that charging is finished (when current changes direction). This timestamp allows the user to
calculate the amount of time the battery has been in a discharge or storage state, again to facilitate self-
discharge calculations.
The format of the ETM, Disconnect, and End-of-Charge registers are as shown in Table 10. Refer to the
“Memory Map” section for the address location of the time-related registers.
TIME REGISTER FORMAT
Table 10
2
7
2
6
2
5
2
4
2
3
2
2
2
1
2
0
LSB
MSb
(unit = 1s)
LSb
2
15
2
14
2
13
2
12
2
11
2
10
2
9
2
8
MSb
(unit = 1s)
LSb
2
23
2
22
2
21
2
20
2
19
2
18
2
17
2
16
MSb
(unit = 1s)
LSb
2
31
2
30
2
29
2
28
2
27
2
26
2
25
2
24
MSB
64-BIT LASERED ROM
Each DS2438 contains a unique ROM code that is 64 bits long. The first 8 bits are a 1-Wire family code
(DS2438 code is 26h). The next 48 bits are a unique serial number. The last 8 bits are a CRC of the first
56 bits. (See Figure 3.) The 64-bit ROM and ROM Function Control section allow the DS2438 to operate
as a 1-Wire device and follow the 1-Wire protocol detailed in the section “1-Wire Bus System.” The
functions required to control sections of the DS2438 are not accessible until the ROM function protocol
has been satisfied. This protocol is described in the ROM function protocol flow chart (Figure 5). The
1-Wire bus master must first provide one of four ROM function commands: 1) Read ROM, 2) Match
ROM, 3) Search ROM, or 4) Skip ROM. After a ROM function sequence has been successfully executed,
the functions specific to the DS2438 are accessible and the bus master may then provide any one of the
six memory and control function commands.
64-BIT LASERED ROM FORMAT
Figure 3
8-BIT CRC CODE
48-BIT SERIAL NUMBER
MSb
8-BIT FAMILY CODE (26h)
MSb
MSb
LSb
LSb
LSb
相關PDF資料
PDF描述
DS2438Z Smart Battery Monitor
DS2442 Battery Management
DS2501 1A VERY LOW DROPOUT VOLTAGE REGULATORS
DS2502 1 kbit Add-Only Memory
DS2502P-E48 48-Bit Node Address Chip
相關代理商/技術參數
參數描述
DS2438AZ 功能描述:IC MONITOR SMART BATTERY 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT
DS2438AZ/T&R 制造商:Maxim Integrated Products 功能描述:SMART BATTERY MONITOR 8-SOIC/T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MONITOR SMART BATTERY 8-SOIC
DS2438AZ/T&R 功能描述:IC MONITOR SMART BATTERY 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT
DS2438AZ+ 功能描述:電池管理 Smart Battery Monitor RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
DS2438AZ+ 制造商:Maxim Integrated Products 功能描述:IC BATTERY MONITOR LI-ION 10V SOIC-8
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*