參數資料
型號： DS2434S
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： Memory IC:Other
英文描述： SPECIALTY MEMORY CIRCUIT, PDSO16
封裝： 0.209 INCH, SSOP-16
文件頁數： 5/20頁
文件大小： 1152K
代理商： DS2434S
DS2434
13 of 20
The initialization sequence required to begin any communication with the DS2434 is shown in Figure 5.
A reset pulse followed by a presence pulse indicates the DS2434 is ready to send or receive data given the
correct memory function command.
The bus master transmits (TX) a reset pulse (a low signal for a minimum of 480
s). The bus master then
releases the line and goes into a receive mode (RX). The 1-Wire bus is pulled to a high state via the
5k-pullup resistor. After detecting the rising edge on the I/O pin, the DS2434 waits 15-60
s and then
transmits the presence pulse (a low signal for 60-240
s).
READ/WRITE TIME SLOTS
DS2434 data is read and written through the use of time slots to manipulate bits and a command word to
specify the transaction.
Write Time Slots
A write time slot is initiated when the host pulls the data line from a high logic level to a low logic level.
There are two types of write time slots: Write 1 time slots and Write 0 time slots. All write time slots
must be a minimum of 60
s in duration with a minimum of a 1 s recovery time between individual
write cycles.
The DS2434 samples the I/O line in a window of 15
s to 60 s after the I/O line falls. If the line is high,
a Write 1 occurs. If the line is low, a Write 0 occurs (see Figure 6).
For the host to generate a Write 1 time slot, the data line must be pulled to a logic low level and then
released, allowing the data line to pull up to a high level within 15
s after the start of the write time slot.
For the host to generate a Write 0 time slot, the data line must be pulled to a logic low level and remain
low for the duration of the write time slot.
Read Time Slots
The host generates read time slots when data is to be read from the DS2434. A read time slot is initiated
when the host pulls the data line from a logic high level to logic low level. The data line must remain at a
low logic level for a minimum of 1
s; output data from the DS2434 is then valid for the next 14 s
maximum. The host therefore must stop driving the I/O pin low in order to read its state 15
s from the
start of the read slot (see Figure 6). By the end of the read time slot, the I/O pin will pull back high via the
external pull-up resistor. All read time slots must be a minimum of 60
s in duration with a minimum of a
1
s recovery time between individual read slots.
Figure 7 shows that the sum of TINIT, TRC , and TSAMPLE must be less than 15
s. Figure 9 shows that
system timing margin is maximized by keeping TINIT and TRC as small as possible and by locating the
master sample time towards the end of the 15
s period.
相關PDF資料
PDF描述
DS2434 SPECIALTY MEMORY CIRCUIT, PBCY3
DS2435 SPECIALTY MEMORY CIRCUIT, PBCY3
DS2436B SPECIALTY MEMORY CIRCUIT, PBCY3
DS2436Z SPECIALTY MEMORY CIRCUIT, PDSO8
DS2490S UNIVERSAL SERIAL BUS CONTROLLER, PDSO24
相關代理商/技術參數
參數描述
DS2434S/T&R 制造商:Maxim Integrated Products 功能描述:BATTERY ID THERMOMTR 16SSOP T&R - Tape and Reel
DS2434S-C01 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
DS2434S-C04 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
DS2434S-C04/T&R 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
DS2434S-C06 制造商:Maxim Integrated Products 功能描述:- Rail/Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*