- 您現在的位置：買賣IC網 > PDF目錄97868 > DS2430AP (MAXIM INTEGRATED PRODUCTS INC) 256 X 1 1-WIRE SERIAL EEPROM, PDSO6 PDF資料下載
參數資料
| 型號： | DS2430AP |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Programmable ROM |
| 英文描述： | 256 X 1 1-WIRE SERIAL EEPROM, PDSO6 |
| 封裝： | 3.70 X 4 MM, 1.50 MM HEIGHT, TSOC-6 |
| 文件頁數： | 16/16頁 |
| 文件大小： | 1683K |
| 代理商： | DS2430AP |
DS2430A
9 of 16
1-WIRE BUS SYSTEM
The 1-Wire bus is a system that has a single bus master and one or more slaves. In all instances, the
DS2430A is a slave device. The bus master is typically a microcontroller. The discussion of this bus
system is broken down into three topics: hardware configuration, transaction sequence, and 1-Wire
signaling (signal type and timing). A 1-Wire protocol defines bus transactions in terms of the bus state
during specified time slots that are initiated on the falling edge of sync pulses from the bus master.
Hardware Configuration
The 1-Wire bus has only a single line by definition; it is important that each device on the bus be able to
drive it at the appropriate time. To facilitate this, each device attached to the 1-Wire bus must have open
drain connection or three-state outputs. The 1-Wire port of the DS2430A is open drain with an internal
circuit equivalent to that shown in Figure 7. A multidrop bus consists of a 1-Wire bus with multiple
slaves attached. The DS2430A communicates at regular 1-Wire speed, 16.3kbits per second, and requires
a pullup resistor as shown in Figure 7. The idle state for the 1-Wire bus is high. If for any reason a
transaction needs to be suspended, the bus MUST be left in the idle state if the transaction is to resume. If
this does not occur and the bus is left low for more than 120s, one or more of the devices on the bus may
be reset.
HARDWARE CONFIGURATION Figure 7
Note: Depending on the 1-Wire communication speed and the bus characteristics, the optimal pullup
resistor value will be in the 1.5k
Ω to 5kΩ range. To write to a single device, a 2.2kΩ resistor and VPUP of
at least 4.0V is sufficient. For writing multiple DS2430As simultaneously or operation at low VPUP, the
resistor should be bypassed by a low-impedance pullup to VPUP while the device copies the scratchpad to
EEPROM.
RPU
Not
Recommended
for
New
Design
相關PDF資料 |
PDF描述 |
|---|---|
| DS2430A | 32 X 8 1-WIRE SERIAL EEPROM, PBCY3 |
| DS2430AX | 32 X 8 1-WIRE SERIAL EEPROM, UUC2 |
| DS2432P/T&R | 1K X 1 1-WIRE SERIAL EEPROM, PDSO6 |
| DS2432X | 1K X 1 1-WIRE SERIAL EEPROM, PBGA6 |
| DS2432P | 1K X 1 1-WIRE SERIAL EEPROM, PDSO6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2430AP R | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:256-Bit 1-Wire EEPROM |
| DS2430AP T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:256-Bit 1-Wire EEPROM |
| DS2430AP/R | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:256-Bit 1-Wire EEPROM |
| DS2430AP/T | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:256-Bit 1-Wire EEPROM |
| DS2430AP/T&R | 功能描述:電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。