參數資料
型號： DS2423P
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： Memory IC:Other
英文描述： SPECIALTY MEMORY CIRCUIT, PDSO6
封裝： 3.70 X 4 MM, 1.50 MM HEIGHT, TSOC-6
文件頁數： 11/25頁
文件大?。?/td> 581K
代理商： DS2423P
DS2423
19 of 25
1-WIRE SIGNALING
The DS2423 requires strict protocols to ensure data integrity. The protocol consists of four types of
signaling on one line: Reset Sequence with Reset Pulse and Presence Pulse, Write 0, Write 1 and Read
Data. The bus master initiates all these signals except Presence Pulse. The DS2423 can communicate at
two different speeds, regular speed and Overdrive speed. If not explicitly set into the Overdrive mode, the
DS2423 will communicate at regular speed. While in Overdrive mode the fast timing applies to all
waveforms.
The initialization sequence required to begin any communication with the DS2423 is shown in Figure 10.
A Reset Pulse followed by a Presence Pulse indicates the DS2423 is ready to send or receive data given
the correct ROM command and memory function command. The bus master transmits (TX) a Reset
Pulse (tRSTL, minimum 480 s at regular speed, 48 s at Overdrive speed). The bus master then releases
the line and goes into receive mode (RX). The 1-Wire bus is pulled to a high state via the pullup resistor.
After detecting the rising edge on the data pin, the DS2423 waits (tPDH, 15-60s at regular speed, 2-6s at
Overdrive speed) and then transmits the Presence Pulse (tPDL, 60-240s at regular speed, 8-24s at
Overdrive speed).
A Reset Pulse of 480s or longer will exit the Overdrive mode returning the device to regular speed. If
the DS2423 is in Overdrive mode and the Reset Pulse is no longer than 80s the device will remain in
Overdrive mode.
Read/Write Time Slots
The definitions of write and read time slots are illustrated in Figure 11. All time slots are initiated by the
master driving the data line low. The falling edge of the data line synchronizes the DS2423 to the master
by triggering a delay circuit in the DS2423. During write time slots, the delay circuit determines when the
DS2423 will sample the data line. For a read data time slot, if a “0” is to be transmitted, the delay circuit
determines how long the DS2423 will hold the data line low overriding the 1 generated by the master. If
the data bit is a “1”, the device will leave the read data time slot unchanged.
INITIALIZATION PROCEDURE “RESET AND PRESENCE PULSES” Figure 10
DS2423
Not
Recommended
for
New
Design
相關PDF資料
PDF描述
DS2423X SPECIALTY MEMORY CIRCUIT, UUC
DS2423 4K X 1 STANDARD SRAM, PDSO6
DS2422 1K X 1 STANDARD SRAM, PDSO6
DS2430AP 256 X 1 1-WIRE SERIAL EEPROM, PDSO6
DS2430A 32 X 8 1-WIRE SERIAL EEPROM, PBCY3
相關代理商/技術參數
參數描述
DS2423P/R 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:4kbit 1-Wire RAM with Counter
DS2423P/T 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:4kbit 1-Wire RAM with Counter
DS2423P/T&R 功能描述:靜態隨機存取存儲器 RoHS:否 制造商:Cypress Semiconductor 存儲容量:16 Mbit 組織:1 M x 16 訪問時間:55 ns 電源電壓-最大:3.6 V 電源電壓-最小:2.2 V 最大工作電流:22 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TSOP-48 封裝:Tray
DS2423P+ 功能描述:靜態隨機存取存儲器 RoHS:否 制造商:Cypress Semiconductor 存儲容量:16 Mbit 組織:1 M x 16 訪問時間:55 ns 電源電壓-最大:3.6 V 電源電壓-最小:2.2 V 最大工作電流:22 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TSOP-48 封裝:Tray
DS2423P+T&R 制造商:Rochester Electronics LLC 功能描述: 制造商:DSC 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*