- 您現在的位置：買賣IC網 > PDF目錄97868 > DS2417P (MAXIM INTEGRATED PRODUCTS INC) 0 TIMER(S), REAL TIME CLOCK, PDSO6 PDF資料下載
參數資料
| 型號： | DS2417P |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Timer or RTC |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDSO6 |
| 封裝： | TSOC-6 |
| 文件頁數： | 2/15頁 |
| 文件大小： | 162K |
| 代理商： | DS2417P |
DS2417
1–WIRE SIGNALING
The DS2417 requires strict protocols to ensure data integrity. The protocol consists of four types of sig-
naling on one line: Reset Sequence with Reset Pulse and Presence Pulse, Write 0, Write 1, and Read
Data. Except for the presence pulse the bus master initiates all these signals.
The initialization sequence required to begin any communication with the DS2417 is shown in Figure 8.
A reset pulse followed by a presence pulse indicates the DS2417 is ready to send or receive data. The bus
master transmits (TX) a reset pulse (tRSTL, minimum 480s). The bus master then releases the line and
goes into receive mode (RX). The 1-Wire bus is pulled to a high state via the pullup resistor. After
detecting the rising edge on the data line, the DS2417 waits (tPDH, 15μs to 60μs) and then transmits the
presence pulse (tPDL, 60μs to 240μs).
INITIALIZATION PROCEDURE “RESET AND PRESENCE PULSES” Figure 8
RESISTOR
MASTER
DS2417
MASTER RX "PRESENCE PULSE"
480 s tRSTL < *
480 s tRSTH < **
15 s tPDH < 60 s
60 t
PDL < 240 s
MASTER TX
"RESET PULSE"
VPULLUP
PULLUP MIN
VIH MIN
VIL MAX
0V
tRSTH
tRSTL
tPDH
tPDL
tR
V
*
In order not to mask interrupt signaling by other devices on the 1-Wire bus tRSTL + tR should al-
ways be less than 960s.
**
Includes recovery time
READ/WRITE TIME SLOTS
The definitions of write and read time slots are illustrated in Figure 9. The master initiates all time slots
by driving the data line low. The falling edge of the data line synchronizes the DS2417 to the master by
triggering an internal delay circuit. During write time slots, the delay circuit determines when the
DS2417 will sample the data line. For a read data time slot, if a “0” is to be transmitted, the delay circuit
determines how long the DS2417 will hold the data line low. If the data bit is a “1”, the DS2417 will not
hold the data line low at all.
10 of 15
相關PDF資料 |
PDF描述 |
|---|---|
| DS2422X | SPECIALTY MEMORY CIRCUIT, UUC |
| DS2423P/T&R | SPECIALTY MEMORY CIRCUIT, PDSO6 |
| DS2423P | SPECIALTY MEMORY CIRCUIT, PDSO6 |
| DS2423X | SPECIALTY MEMORY CIRCUIT, UUC |
| DS2423 | 4K X 1 STANDARD SRAM, PDSO6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2417P/T&R | 制造商:Maxim Integrated Products 功能描述:IC TIMECHIP W/INTRPT 1WIRE 6TSOC |
| DS2417P/T&R | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS2417P+ | 功能描述:實時時鐘 1-Wire w/Interrupt RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS2417P+T&R | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 6PIN TSOC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TIMECHIP W/INTRPT 1WIRE 6TSOC 制造商:Maxim Integrated Products 功能描述:Real Time Clock 1-Wire w/Interrupt |
| DS2417P+T&R | 功能描述:實時時鐘 1-Wire w/Interrupt RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。