- 您現在的位置：買賣IC網 > PDF目錄11740 > DS2406+T&R (Maxim Integrated Products)IC SW DL ADDRESS W/1K MEM TO-92 PDF資料下載
參數資料
| 型號： | DS2406+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 16/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SW DL ADDRESS W/1K MEM TO-92 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,000 |
| 應用： | 遙控，遙測 |
| 接口： | 1 線 |
| 電源電壓： | 2.8 V ~ 6 V |
| 封裝/外殼： | TO-226-3、TO-92-3（TO-226AA）成形引線 |
| 供應商設備封裝： | TO-92-3 |
| 包裝： | 帶卷 (TR) |
| 安裝類型： | 通孔 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
DS2406
23 of 32
1-WIRE SIGNALING
The DS2406 requires strict protocols to ensure data integrity. The protocol consists of five types of
signaling on one line: Reset Sequence with Reset Pulse and Presence Pulse, Write 0, Write 1, Read Data,
and Program Pulse. Except for the presence pulse the bus master initiates all these signals.
The initialization sequence required to begin any communication with the DS2406 is shown in Figure 14.
A reset pulse followed by a presence pulse indicates the DS2406 is ready to send or receive data. The bus
master transmits (TX) a reset pulse (tRSTL, minimum 480s). The bus master then releases the line and
goes into receive mode (RX). The 1-Wire bus is pulled to a high state via the pull-up resistor. After
detecting the rising edge on the data pin, the DS2406 waits (tPDH, 15-60s) and then transmits the
presence pulse (tPDL, 60-240s).
INITIALIZATION PROCEDURE “RESET AND PRESENCE PULSES” Figure 14
RESISTOR
MASTER
DS2406
MASTER RX "PRESENCE PULSE"
480 s ≤ tRSTL < ∞*
480 s ≤ tRSTH < ∞ (includes recovery time)
15 s ≤ tPDH < 60 s
60 ≤ t
PDL < 240 s
MASTER TX
"RESET PULSE"
VPULLUP
VPULLUP MIN
VIH MIN
VIL MAX
0V
tRSTH
tRSTL
tPDH
tPDL
tR
* In order not to mask interrupt signaling by other devices on the 1-Wire bus, tRSTL + tR should
always be less than 960s. In a parasitically powered environment tRSTL should be limited to
maximum 5ms. Otherwise the DS2406 may perform a power-on reset.
READ/WRITE TIME SLOTS
The definitions of write and read time slots are illustrated in Figure 15. The master initiates all time slots
by driving the data line low. The falling edge of the data line synchronizes the DS2406 to the master by
triggering an internal delay circuit. During write time slots, the delay circuit determines when the DS2406
will sample the data line. For a read data time slot, if a “0” is to be transmitted, the delay circuit
determines how long the DS2406 will hold the data line low. If the data bit is a “1”, the DS2406 will not
hold the data line low at all.
相關PDF資料 |
PDF描述 |
|---|---|
| V300A24E500BL | CONVERTER MOD DC/DC 24V 500W |
| VI-B0X-IX-F1 | CONVERTER MOD DC/DC 5.2V 75W |
| VI-B0W-IX-F3 | CONVERTER MOD DC/DC 5.5V 75W |
| V300A24E500B3 | CONVERTER MOD DC/DC 24V 500W |
| V300C28H150BG2 | CONVERTER MOD DC/DC 28V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2406V | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Addressable Switch Plus 1K-Bit Memory |
| DS2406X | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2407 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Addressable Switch Plus 1K.Bit Memory |
| DS2407FP000 | 制造商:Thomas & Betts 功能描述:200A,CON,3P4W,MG,407,3P250V |
| DS2407MP000 | 制造商:Thomas & Betts 功能描述:200A,PLG,3P4W,MG,407,3P250V |
發布緊急采購，3分鐘左右您將得到回復。