- 您現在的位置：買賣IC網 > PDF目錄93261 > DS21T09S (DALLAS SEMICONDUCTOR) 18-LINE 110 ohm SCSI BUS TERMINATOR, PDSO28 PDF資料下載
參數資料
| 型號： | DS21T09S |
| 廠商： | DALLAS SEMICONDUCTOR |
| 元件分類： | Bus Terminator |
| 英文描述： | 18-LINE 110 ohm SCSI BUS TERMINATOR, PDSO28 |
| 封裝： | 0.300 INCH, SOIC-28 |
| 文件頁數： | 5/10頁 |
| 文件大小： | 221K |
| 代理商： | DS21T09S |
DS21T09
4 of 10
DETAILED PIN DESCRIPTION Table 1
PIN
SYMBOL
FCN
DESCRIPTION
1
PDI
I
Power-Down Internal. For Bus Ground Sensing Circuit, connect to pin
22 of internal SCSI connector; see Figure 4.
2-6,
10-13,
16-19,
24-27
R1…R13
R15…R18
T
Signal Termination. 110 termination. Connect to SCSI bus signal
lines. For Bus Current Sensing Circuit connect to data, parity, and
control lines, except SCSI-RST line; see Figure 6.
7, 8, 21
HS-GND
P
Heat Sink Ground. Internally connected to the mounting pad. Should
be either grounded or electronically isolated from other circuitry.
9
PDO
O
Power-Down Output. Connect to DS21T07 for Wide SCSI
applications; see Figure 8.
14
TPWR
P
Termination Power. Connect to the SCSI TERMPWR line. Bypass
with a 2.2 F capacitor; see Figures 4 and 6.
15
VREF
O
Reference Voltage. 2.85-volt reference; must be decoupled with a 4.7
F capacitor; see Figures 4 and 6.
20
PDE
I
Power-Down External. For Bus Ground Sensing Circuit, connect to pin
36 of external SCSI connector; see Figure 4.
22
TCS
I
Termination Current Sense. Used to sense current on the SCSI bus.
For Bus Current Sensing Circuit, connect to SCSI signal line –RST; see
Figure 6.
23
R14
T
Signal Termination. 110 termination. Connect to SCSI bus signal
lines. For Bus Current Sensing Circuit connect to SCSI controller chip;
see Figure 6.
28
GND
P
Ground. Signal ground; 0.0 volts.
ACTIVE TERMINATION
The voltage regulator circuitry (bandgap reference and class AB power amplifier) produces a precise,
laser-trimmed 2.85-volt level and is capable of sourcing 25 mA into each of the terminating resistors
when the signal line is low (active). When the external driver for a given signal line turns off, the active
terminator will pull that signal line to 2.85 volts (quiescent state). When used with an active negation
driver, the power amp can sink 22 mA per line while keeping the voltage reference in regulation; the
terminating resistors maintain their 110
=value over the entire voltage range and Vref will move less than
60 mv. To maintain the specified regulation, a 4.7
F capacitor is required between the VREF pin and
ground. A high frequency capacitor (0.1
F ceramic recommended) can also be placed on the Vref pin in
applications that use fast rise/fall time drivers. The power down capacitance on terminating resistors R1-
R13 and R15-R18 is <3 pF; R14 is slightly higher due to the bus current sensing circuitry.
The DS21T09 can be removed from the SCSI bus by using either of two automatic methods: Bus Ground
Sensing or Bus Current Sensing.
As with all analog circuitry, the TERMPWR lines should be bypassed locally. A 2.2
F capacitor is
recommended between TPWR and ground. It should be placed as close as possible to the DS21T09. The
DS21T09 should be placed as close as possible to the connector to minimize signal and power trace
length, thereby resulting in less input capacitance and reflections which can degrade the bus signals.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2223 | 256 X 1 STANDARD SRAM, 1000 ns, PBCY3 |
| DS2223Z | 256 X 1 STANDARD SRAM, 1000 ns, PDSO4 |
| DS2224 | 224 X 1 STANDARD SRAM, 1000 ns, PBCY3 |
| DS2224Z | 224 X 1 STANDARD SRAM, 1000 ns, PDSO4 |
| DS2227-100 | 512K X 8 NON-VOLATILE SRAM MODULE, 100 ns, SMA72 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS21T09S/T&R | 制造商:Maxim Integrated Products 功能描述:IC TERMINATOR SCSI P&P 28-SOIC |
| DS21T09S/T&R | 功能描述:IC TERMINATOR SCSI P&P 28-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 信號終端器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:SCSI，SE 端子數:9 電源電壓:4 V ~ 5.25 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件 |
| DS21T09S+ | 功能描述:SCSI 接口集成電路 RoHS:否 制造商:Texas Instruments 工作電源電壓:2.7 V to 5.25 V 電源電流:13 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 安裝風格:SMD/SMT 封裝 / 箱體:SSOP-36 封裝:Tube |
| DS21T11 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Terminator |
| DS21T11S | 功能描述:SCSI 接口集成電路 RoHS:否 制造商:Texas Instruments 工作電源電壓:2.7 V to 5.25 V 電源電流:13 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 安裝風格:SMD/SMT 封裝 / 箱體:SSOP-36 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。