- 您現在的位置：買賣IC網 > PDF目錄9759 > DS2149QN+ (Maxim Integrated Products)IC LIU T1/J1 5V 28-PLCC PDF資料下載
參數資料
| 型號： | DS2149QN+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/32頁 |
| 文件大小： | 0K |
| 描述： | IC LIU T1/J1 5V 28-PLCC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 37 |
| 類型： | 線路接口裝置（LIU） |
| 規程： | T1/J1 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-LCC（J 形引線） |
| 供應商設備封裝： | 28-PLCC（11.51x11.51） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
DS2149
15 of 32
5. TRANSMITTER
5.1 Transmit Digital Data Interface
Data is clocked into the device at the TCLK rate. In bipolar mode, TPOS and TNEG are the data inputs;
in NRZ mode, TDATA is the data input. Input data can pass through either the jitter attenuator or the
B8ZS encoder or both. In software mode, setting ENCENB enables B8ZS encoding. In hardware mode,
floating the MODE1 pin enables B8ZS encoding. With B8ZS encoding enabled, the L0 through L3 inputs
determine the coding and is listed in Table 4-E. TCLK supplies input synchronization. See Section 12 for
the TCLK and MCLK timing requirements.
5.2 Transmit Monitoring
In software mode, the DFMO bit in the status register is set when an open circuit in the transmitter path is
detected. A transition on this bit can provide an interrupt, and a transition sets the DFMO bit in the
transition status register. Setting CDFMO in the interrupt mask register, leaving a 1 in that bit location
masks the interrupt.
5.3 Transmit Idle Mode
Transmit idle mode allows multiple transceivers to be connected to a single line for redundant
applications. When TCLK is not present, transmit idle mode becomes active, and TTIP and TRING
change to high-impedance state. Remote loopback, dual loopback, TAIS, or detection of network loop-up
code in the receive direction temporarily disable the high-impedance state.
5.4 Transmit Pulse Shape
As shown in Table 4-E, line build-out control inputs (L0 through L3) determine the transmit pulse shape.
In software mode, these control inputs are located in control register 1; in hardware mode, these control
inputs are the L0 through L3 pins.
Shaped pulses meeting the various T1, DS1, and DSX-1 specifications are applied to the AMI line driver
for transmission onto the line at TTIP and TRING. The transceiver produces DSX-1 pulses for short-haul
T1 applications (settings from 0dB to 6dB of cable) and DS1 pulses for long-haul T1 applications
(settings from 0dB to -22.5dB). Refer to Table 4-E for pulse mask specifications.
6. RECEIVER
A 1:1 transformer provides the interface between the twisted pair and receiver inputs RTIP and RRING.
Recovered data is output at RPOS and RNEG (or RDATA in NRZ mode), and the recovered clock is
output at RCLK. See Section 12 for receiver timing specifications.
6.1 Receive Equalizer
The receiver can apply up to 36dB of gain. Control of the equalizer is accomplished by the L0 through L3
control inputs. These control signals are detailed in Table 4-E and determine the maximum gain that is
applied. In software mode, these control signals are in Control Register 1; in hardware mode, these
control inputs are the L0 through L3 pins. With L0 low, up to 36dB of gain can be applied; when L0 is
high, 26dB can be applied in the gain limit to provide better noise immunity in shorter loop operations.
6.2 Receive Data Recovery
The clock and data recovery engine provides input jitter tolerance that exceeds the requirements of AT&T
62411. Inbound signal is filtered, equalized, and over-sampled 16 times. Then it is applied to the B8ZS
decoder if enabled.
相關PDF資料 |
PDF描述 |
|---|---|
| DS21348GN | IC LIU LN T1/E1/J1 3.3V 49-BGA |
| VI-241-MX-F3 | CONVERTER MOD DC/DC 12V 75W |
| MAX214EPI+ | IC TXRX RS-232 PROG 28-DIP |
| MAX214EWI+ | IC TXRX RS-232 PROG 28-SOIC |
| HI5767/2IA | CONV A/D 10BIT 20MSPS 28-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2149QN/T&R | 制造商:Maxim Integrated Products 功能描述:IC LINE INTERFACE 5V T1/J1 PLCC 制造商:Maxim Integrated Products 功能描述:Network Controller & Processor ICs 5V T1/J1 Line Interface |
| DS2149QN/T&R+ | 制造商:Maxim Integrated Products 功能描述:FRAMER J1/T1 5V 28PLCC - Tape and Reel |
| DS2149QN/T&R | 功能描述:網絡控制器與處理器 IC 5V T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2149QN+ | 功能描述:網絡控制器與處理器 IC 5V T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2149QN+T&R | 制造商:Maxim Integrated Products 功能描述:FRAMER J1/T1 5V 28PLCC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:MXMDS2149QN+T&R 5V T1/J1 LIU T&R IND PLC 制造商:Maxim Integrated Products 功能描述:IC LIU T1/J1 5V 28-PLCC 制造商:Maxim Integrated Products 功能描述:Network Controller & Processor ICs 5V T1/J1 Line Interface |
發布緊急采購，3分鐘左右您將得到回復。