參數資料
型號: DS21348TN+
廠商: Maxim Integrated Products
文件頁數: 6/76頁
文件大?。?/td> 0K
描述: IC LIU T1/E1/J1 3.3V 44-TQFP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 160
類型: 線路接口裝置(LIU)
驅動器/接收器數: 1/1
規程: T1/E1/J1
電源電壓: 3.135 V ~ 3.465 V
安裝類型: 表面貼裝
封裝/外殼: 44-TQFP
供應商設備封裝: 44-TQFP(10x10)
包裝: 托盤
產品目錄頁面: 1429 (CN2011-ZH PDF)
DS21348/DS21Q348
14 of 76
2.1 Pin Descriptions
Table 2-5. Pin Descriptions in Parallel Port Mode (Sorted by Pin Name,
DS21348T Pin Numbering)
NAME
PIN
I/O
FUNCTION
A0 to A4
11 to 7
I
Address Bus. In nonmultiplexed bus operation (BIS1 = 0, BIS0 =
1), serves as the address bus. In multiplexed bus operation (BIS1 =
0, BIS0 = 0), these pins are not used and should be tied low.
ALE (AS)
4
I
Address Latch Enable (Address Strobe). When using the parallel
port (BIS1 = 0) in multiplexed bus mode (BIS0 = 0), serves to
demultiplex the bus on a positive-going edge. In nonmultiplexed bus
mode (BIS0 = 1), should be tied low.
BIS0/BIS1
32/33
I
Bus Interface Select Bits 0 and 1. Used to select bus interface
option. See Table 2-1 for details.
BPCLK
31
O
Backplane Clock. A 16.384MHz, 8.192MHz, 4.096MHz, or
2.048MHz clock output that is referenced to RCLK selectable via
CCR5.7 and CCR5.6. In hardware mode, defaults to 16.384MHz
output.
CS
1
I
Chip Select, Active Low. This active-low signal must be low to
read or write to the device.
D0/AD0 to
D7/AD7
19 to 12
I/O
Data Bus/Address/Data Bus. In nonmultiplexed bus operation
(BIS1 = 0, BIS0 = 1), serves as the data bus. In multiplexed bus
operation (BIS1 = 0, BIS0 = 0), serves as an 8-bit multiplexed
address/data bus.
HRST
29
I
Hardware Reset, Active Low. Bringing
HRST low resets the
DS21348, setting all control bits to their default state of all zeros.
INT
23
O
Interrupt, Active Low. Flags host controller during conditions and
change of conditions defined in the Status Register. Active low,
open drain output.
MCLK
30
I
Master Clock. A 2.048MHz (±50ppm) clock source with TTL
levels is applied at this pin. This clock is used internally for both
clock/data recovery and for jitter attenuation. Use of a T1 1.544MHz
clock source is optional.
N/A
I
Not Assigned. Should be tied low.
PBEO
24
O
PRBS Bit Error Output. The receiver will constantly search for a
215-1 or a 220-1 PRBS depending on the ETS bit setting (CCR1.7).
Remains high if out of synchronization with the PRBS pattern. Goes
low when synchronized to the PRBS pattern. Any errors in the
received pattern after synchronization will cause a positive going
pulse (with same period as E1 or T1 clock) synchronous with
RCLK. PRBS bit errors can also be reported to the ECR1 and ECR2
registers by setting CCR6.2 to a logic 1.
相關PDF資料
PDF描述
VE-B5J-MX-F2 CONVERTER MOD DC/DC 36V 75W
VE-B5J-MX-F1 CONVERTER MOD DC/DC 36V 75W
VE-B5J-MW CONVERTER MOD DC/DC 36V 100W
VE-B54-MX-F3 CONVERTER MOD DC/DC 48V 75W
T 3402 000 CONN CIR RCPT MALE 6POS PNL MNT
相關代理商/技術參數
參數描述
DS21348TN+ 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21348TNB 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21348T-W 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21349 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3.3V T1/J1 Line Interface Unit
DS21349DK 功能描述:網絡開發工具 DS21349 Design Kit RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V