參數資料
型號： DS21348T
英文描述： 3.3V E1/T1/J1 Line Interface
中文描述： 3.3 E1/T1/J1線路接口
文件頁數： 30/73頁
文件大?。?/td> 551K
代理商： DS21348T
DS21348/Q348
30 of 73
CCR3 (02H): COMMON CONTROL REGISTER 3
(MSB)
TUA1
ATUA1
TAOZ
(LSB)
IBE
TPRBSE
TLCE
LIRST
IBPV
SYMBOL
POSITION
DESCRIPTION
TUA1
CCR3.7
Transmit Unframed All Ones.
The polarity of this bit is set
such that the device will transmit an all ones pattern on power-
up or device reset. This bit must be set to a one to allow the
device to transmit data. The transmission of this data pattern is
always timed off of the JACLK (See Figure 3-1).
0 = transmit all ones at TTIP and TRING
1 = transmit data normally
Automatic Transmit Unframed All Ones.
Automatically
transmit an unframed all ones pattern at TTIP and TRING
during a receive carrier loss (RCL) condition or receive all ones
condition.
0 = disabled
1 = enabled
Transmit Alternate Ones and Zeros.
Transmit a …101010…
pattern at TTIP and TRING. The transmission of this data
pattern is always timed off of TCLK (See Figure 3-1).
0 = disabled
1 = enabled
Transmit PRBS Enable.
Transmit a 2
15
- 1 (E1) or a 2
20
- 1
(T1) PRBS at TTIP and TRING.
0 = disabled
1 = enabled
Transmit Loop Code Enable.
Enables the transmit side to
transmit the loop up code in the Transmit Code Definition
registers (TCD1 and TCD2). See Section 6 for details.
0 = disabled
1 = enabled
Line Interface Reset.
Setting this bit from a zero to a one will
initiate an internal reset that resets the clock recovery state
machine and re-centers the jitter attenuator. Normally this bit is
only toggled on power-up. Must be cleared and set again for a
subsequent reset.
Insert BPV.
A 0 to 1 transition on this bit will cause a single
BiPolar Violation (BPV) to be inserted into the transmit data
stream. Once this bit has been toggled from a 0 to a 1, the
device waits for the next occurrence of three consecutive ones
to insert the BPV. This bit must be cleared and set again for a
subsequent error to be inserted. See .
Insert Bit Error.
A 0 to 1 transition on this bit will cause a
single logic error to be inserted into the transmit data stream.
This bit must be cleared and set again for a subsequent error to
be inserted. See Figure 3-3.
ATUA1
CCR3.6
TAOZ
CCR3.5
TPRBSE
CCR3.4
TLCE
CCR3.3
LIRST
CCR3.2
IBPV
CCR3.1
IBE
CCR3.0
相關PDF資料
PDF描述
DS21348TN 3.3V E1/T1/J1 Line Interface
DS21352 3.3V DS21352 and 5V DS21552 T1 Single-Chip Transceivers
DS21352L 3.3V DS21352 and 5V DS21552 T1 Single-Chip Transceivers
DS21352LN 3.3V DS21352 and 5V DS21552 T1 Single-Chip Transceivers
DS21552L 3.3V DS21352 and 5V DS21552 T1 Single-Chip Transceivers
相關代理商/技術參數
參數描述
DS21348T+ 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21348TB 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21348TN 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21348TN+ 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21348TNB 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*