- 您現在的位置：買賣IC網 > PDF目錄376964 > DS21348 3.3V E1/T1/J1 Line Interface PDF資料下載
參數資料
| 型號： | DS21348 |
| 英文描述： | 3.3V E1/T1/J1 Line Interface |
| 中文描述： | 3.3V、E1/T1/J1線路接口 |
| 文件頁數： | 11/73頁 |
| 文件大?。?/td> | 551K |
| 代理商： | DS21348 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁
DS21348/Q348
11 of 73
PIN DESCRIPTIONS IN PARALLEL PORT MODE
(
Sorted by Pin Name,
DS21348T Pin Numbering
) Table 4-2b
ACRONYM
PIN
I/O
DESCRIPTION
A0 to A4
11
to
7
4
I
Address Bus.
In nonmultiplexed bus operation (BIS1 = 0, BIS0 =
1), serves as the address bus. In multiplexed bus operation (BIS1 =
0, BIS0 = 0), these pins are not used and should be tied low.
Address Latch Enable (Address Strobe).
When using the parallel
port (BIS1 = 0) in multiplexed bus mode (BIS0 = 0), serves to
demultiplex the bus on a positive-going edge. In nonmultiplexed bus
mode (BIS0 = 1), should be tied low.
Bus Interface Select Bits 0 & 1.
Used to select bus interface option.
See Table 4-1 for details.
Back Plane Clock.
A 16.384MHz, 8.192MHz, 4.096MHz, or
2.048MHz clock output that is referenced to RCLK selectable via
CCR5.7 and CCR5.6. In hardware mode, defaults to 16.384MHz
output.
Chip Select.
Must be low to read or write to the device. CS* is an
active low signal.
Data Bus/Address/Data Bus.
In nonmultiplexed bus operation
(BIS1 = 0, BIS0 = 1), serves as the data bus. In multiplexed bus
operation (BIS1 = 0, BIS0 = 0), serves as an 8-bit multiplexed
address/data bus.
Hardware Reset.
Bringing HRST* low will reset the DS21348
setting all control bits to their default state of all zeros.
Interrupt [INT*] Pin 23.
Flags host controller during conditions
and change of conditions defined in the Status Register. Active low,
open drain output.
Master Clock.
A 2.048MHz (±50ppm) clock source with TTL
levels is applied at this pin. This clock is used internally for both
clock/data recovery and for jitter attenuation. Use of a T1 1.544
MHz clock source is optional.
See Note 2.
Not Assigned.
Should be tied low.
PRBS Bit Error Output.
The receiver will constantly search for a
2
15
-1 or a 2
20
-1 PRBS depending on the ETS bit setting (CCR1.7).
Remains high if out of synchronization with the PRBS pattern. Goes
low when synchronized to the PRBS pattern. Any errors in the
received pattern after synchronization will cause a positive going
pulse (with same period as E1 or T1 clock) synchronous with
RCLK. PRBS bit errors can also be reported to the ECR1 and ECR2
registers by setting CCR6.2 to a logic 1.
Parallel Bus Type Select.
When using the parallel port (BIS1 = 0),
set high to select Motorola bus timing, set low to select Intel bus
timing. This pin controls the function of the RD*(DS*), ALE(AS),
and WR*(R/W*) pins. If PBTS = 1 and BIS1 = 0, then these pins
assume the Motorola function listed in parenthesis (). In serial port
mode, this pin should be tied low.
ALE(AS)
I
BIS0/BIS1
32/33
I
BPCLK
31
O
CS*
1
I
D0 / AD0
to
D7 / AD7
19
to
12
I/O
HRST*
29
I
INT*
23
O
MCLK
30
I
NA
PBEO
-
I
24
O
PBTS
44
I
相關PDF資料 |
PDF描述 |
|---|---|
| DS21348T | 3.3V E1/T1/J1 Line Interface |
| DS21348TN | 3.3V E1/T1/J1 Line Interface |
| DS21352 | 3.3V DS21352 and 5V DS21552 T1 Single-Chip Transceivers |
| DS21352L | 3.3V DS21352 and 5V DS21552 T1 Single-Chip Transceivers |
| DS21352LN | 3.3V DS21352 and 5V DS21552 T1 Single-Chip Transceivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS21348DK | 功能描述:網絡開發工具 DS21348 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V |
| DS21348G | 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21348G+ | 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21348G+W | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21348GB | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。