- 您現在的位置：買賣IC網 > PDF目錄376964 > DS2109 Plug and Play SCSI Terminator PDF資料下載
參數資料
| 型號： | DS2109 |
| 英文描述： | Plug and Play SCSI Terminator |
| 中文描述： | 即插即用的SCSI終結者 |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 85K |
| 代理商： | DS2109 |
DS2109
022698 6/10
BUS CURRENT SENSING
The DS2109 has the capability to use current sensing to
determine if the SCSI bus is over– or under–terminated.
A series 1 ohm resistor between pads R14 and TCS is
inserted into the SCSI bus (preferably the –RST line)
and used to monitor the current when that line pulls low
(active, or “asserted” state). Based on the current mea-
sured, the DS2109 will disconnect or connect from the
SCSI bus. The configuration for this automatic isolation
technique is shown in Figure 6.
Figure 5 shows a simplified diagram of the sensing cir-
cuit. The voltage across the 1 ohm sense resistor is dif-
ferentially amplified and converted into a single–ended
voltage with respect to ground. This is fed into a bank of
comparators and measured against a reference volt-
age. The circuit takes a measurement each time TCS is
driven below a 0.8 volts threshold and the outputs are
latched on the rising edge of TCS. If I
BUS
is greater than
32 mA, the DS2109 will be isolated from the SCSI bus. It
is recommended that the signal on TCS be asserted for
at least 25 msec to allow the signal (and comparator out-
puts) to settle into a known state. A timing diagram of the
sensing and latching operation is shown in Figure 7.
It is preferred that the –RST line be used for monitoring
the bus termination status because –RST is only
asserted during power up or during a major change in
bus configuration. Note that R14 will have a higher input
capacitance than the other lines because of the addi-
tional circuitry required for bus sensing.
The DS2109 will be isolated from the SCSI bus as
shown in Table 2.
BUS CURRENT SENSING CIRCUITRY
Figure 5
REF
DECODE
LAND
TCS
R14
1 OHM
110 OHM
+
–
I
BUS
TO SCSI CONTROLLER
FROM SCSI BUS (–RST)
相關PDF資料 |
PDF描述 |
|---|---|
| DS2110 | Interface IC |
| DS2114Z | CORD TIE;BUCKLE,GROMMET |
| DS2116E | Terminator |
| DS2119ME | Terminator |
| DS211E | Interface IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2109DK | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Demo Board |
| DS2109S | 功能描述:IC TERM SCSI PLUG/PLAY 28-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 信號終端器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:SCSI，SE 端子數:9 電源電壓:4 V ~ 5.25 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件 |
| DS2109S/T&R | 制造商:Maxim Integrated Products 功能描述:PNP SCSI TERMINATOR 28P SOIC-TRL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TERM SCSI PLUG/PLAY 28-SOIC |
| DS2109S/T&R | 功能描述:IC TERM SCSI PLUG/PLAY 28-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 信號終端器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:SCSI，SE 端子數:9 電源電壓:4 V ~ 5.25 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件 |
| DS2109S-T | 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。