- 您現在的位置：買賣IC網 > PDF目錄97865 > DS18S20-PAR/T&R (MAXIM INTEGRATED PRODUCTS INC) DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 0.50Cel, ROUND, THROUGH HOLE MOUNT PDF資料下載
參數資料
| 型號： | DS18S20-PAR/T&R |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 0.50Cel, ROUND, THROUGH HOLE MOUNT |
| 封裝： | TO-92, 3 PIN |
| 文件頁數： | 16/20頁 |
| 文件大?。?/td> | 250K |
| 代理商： | DS18S20-PAR/T&R |
DS18S20-PAR
5 of 20
so the master can determine exactly which DS18S20-PARs have experienced an alarm condition. If an
alarm condition exists and the TH or TL settings have changed, another temperature conversion should be
done to validate the alarm condition.
64-BIT LASERED ROM CODE
Each DS18S20-PAR contains a unique 64–bit code (see Figure 5) stored in ROM. The least significant 8
bits of the ROM code contain the DS18S20-PAR’s 1–wire family code: 10h. The next 48 bits contain a
unique serial number. The most significant 8 bits contain a cyclic redundancy check (CRC) byte that is
calculated from the first 56 bits of the ROM code. A detailed explanation of the CRC bits is provided in
the CRC GENERATION section. The 64–bit ROM code and associated ROM function control logic
allow the DS18S20-PAR to operate as a 1–wire device using the protocol detailed in the 1-WIRE BUS
SYSTEM section of this datasheet.
64-BIT LASERED ROM CODE Figure 5
8-BIT CRC
48-BIT SERIAL NUMBER
8-BIT FAMILY CODE (10h)
MEMORY
The DS18S20-PAR’s memory is organized as shown in Figure 6. The memory consists of an SRAM
scratchpad with nonvolatile EEPROM storage for the high and low alarm trigger registers (TH and TL).
Note that if the DS18S20-PAR alarm function is not used, the TH and TL registers can serve as general-
purpose memory. All memory commands are described in detail in the DS18S20-PAR FUNCTION
COMMANDS section.
Byte 0 and byte 1 of the scratchpad contain the LSB and the MSB of the temperature register,
respectively. These bytes are read-only. Bytes 2 and 3 provide access to TH and TL registers. Bytes 4
and 5 are reserved for internal use by the device and cannot be overwritten; these bytes will return all 1s
when read. Bytes 6 and 7 contain the COUNT REMAIN and COUNT PER C registers, which can be
used to calculate extended resolution results as explained in the OPERATION – MEASURING
TEMPERATURE section. Byte 8 of the scratchpad is read-only and contains the cyclic redundancy
check (CRC) code for bytes 0 through 7 of the scratchpad. The DS18S20-PAR generates this CRC using
the method described in the CRC GENERATION section.
Data is written to bytes 2 and 3 of the scratchpad using the Write Scratchpad [4Eh] command; the data
must be transmitted to the DS18S20-PAR starting with the least significant bit of byte 2. To verify data
integrity, the scratchpad can be read (using the Read Scratchpad [BEh] command) after the data is
written.
When reading the scratchpad, data is transferred over the 1-Wire bus starting with the least
significant bit of byte 0. To transfer the TH and TL data from the scratchpad to EEPROM, the master
must issue the Copy Scratchpad [48h] command.
Data in the EEPROM registers is retained when the device is powered down; at power-up the EEPROM
data is reloaded into the corresponding scratchpad locations. Data can also be reloaded from EEPROM
to the scratchpad at any time using the Recall E
2 [B8h] command. The master can issue “read time slots”
(see the 1-WIRE BUS SYSTEM section) following the Recall E2 command and the DS18S20-PAR will
indicate the status of the recall by transmitting 0 while the recall is in progress and 1 when the recall is
done.
MSB
LSB
MSB
相關PDF資料 |
PDF描述 |
|---|---|
| DS18S20-PAR | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 0.50Cel, ROUND, THROUGH HOLE MOUNT |
| DS18S20Z | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
| DS18S20 | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 0.50Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| DS18S20-SL+T&R | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 0.50Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| DS18S20Z/T&R | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS18S20-SL/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS18S20-SL+T&R | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 1-WIRE - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERM MICROLAN HI-PREC TO-92 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Prgmble Resolution 1-Wire Parasite Pwr |
| DS18S20-SL+T&R | 功能描述:板上安裝溫度傳感器 Prgmble Resolution 1-Wire Parasite Pwr RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS18S20-W | 制造商:Maxim Integrated Products 功能描述: |
| DS18S20Z | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。