參數資料
型號: DS1877T+T&R
廠商: Maxim Integrated Products
文件頁數: 18/65頁
文件大?。?/td> 0K
描述: IC CTLR/MON SFP 1-2CH 28TQFN
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 2,500
類型: SFP+ 控制器
輸入類型: 邏輯
輸出類型: 邏輯
接口: I²C
電流 - 電源: 2.5mA
安裝類型: 表面貼裝
封裝/外殼: 28-WFQFN 裸露焊盤
供應商設備封裝: 28-TQFN-EP(5x5)
包裝: 帶卷 (TR)
其它名稱: 90-1877T+TRL
25
Maxim Integrated
SFP Controller for Dual Rx Interface
DS1877
Register Descriptions
The register maps show each byte/word (2 bytes) in
terms of its row in the memory. The first byte in the row
is located in memory at the row address (hexadecimal)
in the leftmost column. Each subsequent byte on the row
is one/two memory locations beyond the previous byte/
word’s address. A total of 8 bytes are present on each
row. For more information about each of these bytes, see
the corresponding register description.
Memory Map Access Codes
The following section provides the device’s register defi-
nitions. Each register or row of registers has an access
descriptor that determines the password level required
to read or write the memory. Level 2 password is intend-
ed for the module manufacture access only. Level 1
password allows another level of protection for items
the end consumer wishes to protect. Many registers are
always readable, but require password access to write.
There are a few registers that cannot be read without
password access. The following access codes describe
each mode the device uses with factory settings for the
PW_ENA and PW_ENB (Table 02h, Registers C0h–C1h)
registers.
Memory Addresses A0h, A2h, and B2h
There are three separate I2C addresses in the device:
A0h, A2h, and B2h. A2h and B2h are used to configure
and monitor two receivers. Receiver 1 is accessed using
A2h. Receiver 2 is accessed using B2h. Many of the reg-
isters in A2h and B2h are shared registers. These reg-
isters can be read and written from both A2h and B2h.
ACCESS
CODE
READ ACCESS
WRITE ACCESS
<0/_>
At least 1 byte/bit in the row/byte is different
than the rest of the row/byte, so look at each
byte/bit separately for permissions.
<1/_>
Read all
Write PW2
<2/_>
Read all
Write not applicable
<3/_>
Read all
Write all, but the
device hardware
also writes to these
bytes/bits
<4/_>
Read PW2
Write PW2 +
mode_bit
<5/_>
Read all
Write all
<6/_>
Read not applicable
Write all
<7/_>
Read PW1
Write PW1
<8/_>
Read PW2
Write PW2
<9/_>
Read not applicable
Write PW2
<10/_>
Read PW2
Write not applicable
<11/_>
Read all
Write PW1
MEMORY
CODE
A2h AND B2h REGISTERS
<C> or
<_/C>
A common memory location is used for
A2h and B2h device addresses. Reading
or writing to these locations is identical,
regardless of using A2h or B2h addresses.
<D> or
<_/D>
Different memory locations are used for A2h
and B2h device addresses.
<M> or
<_/M>
Mixture of common and different memory
locations for A2h and B2h device address-
es. See the individual bytes within the row
for clarification. If “M” is used on an indi-
vidual byte, see the expanded bit descrip-
tions to determine which bits are common
vs. different.
相關PDF資料
PDF描述
DS1878T+T&R IC CTLR SFP W/DGTL LDD RX 28TQFN
DS1881Z-050+T&R IC DGTL POT NV 2CH 45K 16-SOIC
DS1882Z-050+T&R IC POT DIGIT DL LOG 50K 16SOIC
DS1884AT+T IC SFP PON ONU CTRLR 24TQFN
DS2105Z+ IC SCSI TERMINATOR 16-SOIC
相關代理商/技術參數
參數描述
DS1878 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:SFP+ Controller with Digital LDD Interface
DS1878T 功能描述:ADC / DAC多通道 SFP+ Controller w/ MAX3946&3945 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
DS1878T TR 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:SFP+ Controller with Digital LDD Interface
DS1878T+ 功能描述:ADC / DAC多通道 SFP+ Controller w/ MAX3946&3945 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
DS1878T+T 功能描述:ADC / DAC多通道 SFP+ Controller w/ MAX3946&3945 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40